Hi, As title says, I have a new ASR901 fresh from the box. I'm unable to no shut port 10 or 11 which I believe are flex ports. I recieve an error "license-request_failed:"I believe I understand that I need to activate a license of some sort but after...
Forum Posts
So if you have a multi-layer switch which is connected via layer 2 switchport to another switch heading to main campus and/or out to core network devices, can you install another device let's say router or FW on a port configured for Layer 3 and traf...
I'm trying to open a port to a server using Port Forwarding. When I setup port forwarding to go to a server on the default VLAN, everything works fine, external requests to that port are forwarded to the server and the server responds.However, if I ...
I have a situation where my Internet edge routers learn 0.0 from ATT (AS 7018) my provider. I then wish to advertise these learned routes via WAN. However my WAN MPLS provider is also ATT and they use AS 7018 for that as well. When I try to push 0...
Resolved! Stopbit Command Question
So I am running through some configs that one of our previous engineers used in a router config and came across the stopbit 1 command on line con 0. Can someone explain what the stopbit is and why you would use this command at all? I have just neve...
At least with srr-queue i can sort of do something to manage speeds.. but with upload.. acl.. access group.. policy .. police... jesus.. i can not find one guide that actually works from beginning to end.. im desparate to be able to do this.. im tryi...
Resolved! Cisco ISR Throughput
Hi guys, i'm new to networking and just want to upgrade the old router on my branch. As i read ISR 4321 documentation it states that 50Mbps-100Mbps system throughput. Does it means that if i have 1Gbps internet capability from ISP, with default lice...
Hi, I installed CSR1000v router on my hyper-v with demo license AX 2,5gbps and I tried some throughput test. During testing (around 600MB/s should be 900+) I discovered that one core is fully loaded when others are not. VM router have assigned 4 vcpu...
I have 2 2951 routers, running the same IOS (c2951-universalk9-mz.SPA.156-3.M2.bin). I am setting this up with the Cube license, and while waiting I activated the eval rtu advuck9 license, then ordered what I was told all I needed was the uck9 paper...
How would you use OSPF or EIGRP to get a VRF-Lite SVI network into the routing process? I have seen routing redistribution and a route to a firewall but was wondering if anyone else uses a different way? Or what is the best way? Really stuck on how w...
I create PBR to divert traffic to next hop but it is not workingnot sure where is the wrong configI have 2 core switches to 2 WAN link with Active-PassiveNot sure where to apply the route-map, either on Outgoing interface or on the SVI
We have a dedicated T1 to a remote site. I want to make sure that we have the proper QOS setup. Right now all we have are policy maps that set dscp values. For example: class voice-s0/0bandwidth remaining percent 70set dscp efclass voice is defin...
Hello TogetherI have the router type: ISR4400I wanted to output the "bootflash:" with the command "you"The error message: r-****#dir bootflash: Directory of bootflash:/ No files in directory 7113240576 bytes total (3392778240 bytes free) ----- r...
Resolved! BGP Soft reconfiguration on ASA
I'm running BGP on an ASA 5512-X (Version 9.7(1)) I am trying to see the received routes from a BGP peer before filtering is applied, however I receive this error: # show bgp neighbors 192.168.198.2 received-routes % Inbound soft reconfiguration not...
HiPlease, anyone explain what is the meaning of below marked (blue line) output ThanksSiva
