I'm trying to advertise a prefix from the Hub Routers ( 10.1.0.0/16 ) allowing SD-WAN branches to reach to this segment which is non SD-WAN branch, Whenever i tried to add this specific route under the service VPN , its being categorized as "rt-ext:n...
Forum Posts
Hi It is possible to configure the same network for Service Side NAT pool but in different VPN/VRF? Ex:VPN 1Inside Local : 10.0.100.0/24Inside Global : 192.168.100.0/24 VPN 2Inside Local : 10.0.101.0/24Inside Global : 192.168.100.0/24 Thanks!
Hi Has any one done any cost comparison of various SD-WAN solutions with respect to pricing & cost ?If yes , please share it. Would like to understanding how the SD-WAN costs differs for each product/vendor solutions ? I am looking for cost compariso...
Hello, I have deployed a pair of CSR 8000v in AWS and Azure using Cloud On-ramp for multicloud, and that part was successful, the routers have established BGP, etc. to each cloud provider and to the controllers. This was done mostly by using the def...
Quick question, Whats how are the meraki firewall walls compared to the ASA Firewalls? Why would someone choose one over the other and in what situations? I'm sure one can do what another can't but what warrants that? What are your thoughts about the...
I am trying to understand what the throughput capacity is for a vedge 100b GigabitEthernet port. Assuming I had a 1GB Internet connection terminated on a vedge 100B port, what is the maximum throughput rate I could achieve? I have not found any doc...
2 Quick questions - in a Cisco C8300 can a NIM module be used for TLOC? Also, can you LAG two TLOC Ethernet interfaces? Thank you!!
Resolved! TLOC cannot connect to vSmart
Folks, If a TLOC cannot connect to any vSmart with a TLS/DTLS connection I assume that TLOC is not eligible to create an IPSEC tunnel to another vEdge. I'm assuming here that if the vSmart does not learn about the TLOC it cannot then exchange that in...
HiI have an IR1101 router with Cellular interface(Cellular0/1/0).This interface has a /32 ip address. I need to configure an ip route via this interface but it is not possible with VPN template that only allows next hop. I'm trying with a CLI ADD-ON...
Hi, I am looking for a vManage real-time API which gives us applications on a device. device/dpi/applications API works for vEdges but it returns empty data response for cEdges. Please let me know the corresponding API for cEdge I tried the APIs in t...
Hello, I configure tloc-extension between vedge1 and vedge2. Both of the vedges should have 2 tlocs now, mpls and biz-internet.I can't figure out why if I view the received tlocs from vedge1, all of vedge2 tlocs will have its bfd session as down. Th...
Hi All, I was trying to configure SNMPv3 via vManage on cisco SD-WAN sending logs to LiveNX but for some reason SNMPv3 doesn't seem to be working. When I changed version to v2c , its working but v3 doesn't. However when I run snmpwalk via cli ( on u...
So I have this setup in a newly campus network , where the connectivity almost look like this : Endpoint ---- Access Switch ------ Distribution Switch ---- Firewall ---- Cisco SD-WAN Branch Router =======IPSEC Tunnel==== Cisco SD-WAN Hub site ---- DH...
Hi, I am trying to find information regarding the Layer-2 functionality on integrated ports on C8300-1N1S-4T2X. Does any of the built-in ports support L2 functionality at all? Is it possible to set up a l2 Port-Channel for example or a switch module...
Hi All Using TACACs to login to my vedge100s. ISE is the AAA server. I can log in to the router , but I seem to get "basic" permissions. I want netadmin permissions. Is there some av-pair that I have to send back from TACACs to specify permissio...
