Hi,has anyone tried to configure a dlsw+ peer which is terminated in a vrf ??? Is there any other solution to combine both technologies ??Carsten
Hi,has anyone tried to configure a dlsw+ peer which is terminated in a vrf ??? Is there any other solution to combine both technologies ??Carsten
I have the problem that a Mainframe OSA-2 will not transmit data in any of 3 modules of WS-X6148-RJ45V in a CAT6513, running IOS 121-13.E6.Just about any other Network card/OS (ie 3COM NIC or Intel/UNIX OS) work without issue.A 10mb OSA-2 will work i...
HII need to configure a 7505/4 to receive TCP/IP connections on behalf on the m/f. We will have a cip2 connected to the esconn channel on the m/f. Has any body got any good weblinks showing good practice design and configuration for this. I am lookin...
Hi Experts.My Customer is a Bank with a two-tiered WAN: 100 small remote sites directly connected (leased lines) to HQ.There is also a Medium Regional Site with redundant WAN connection to the HQ. Remote sites and Regional Site have a DLSw peering to...
hi,i need to know if DLSw "local-switching" is supported beetween 2 (or more) Ethernet interfaces on the same router.This is for resolve situation of stations on two differents VLANs and an as400 on another VLAN.Another possibility may be to have onl...
Hello,i'm trying to understand some problems on the ethernet of router cisco3640,i find a lot of collisions and deferred.My topology is :Ethernet---router A ----FM-----router B----Ethernet(10Mb/s) (10Mb/s)and these a...
I have two devices attached via token ring with a wan in the middle.I see circuit established between devices at both ends but not to one device never goes into session.show dlsw circIndex local addr(lsap) remote addr(dsap) state ...
We have a requested requirement to provide 1500 SDLC DSLW connections from 1500 remote locations to 1 data center. While attempting to scope out a router(s) type for the data center, we are trying to dig up what the potential limitation would be for ...
In the quest to provide durability for the network, we are using dual routers at each remote site. I am planning to use the ethernet redundancy feature to be able to use both routers when starting a circuit from the remote site, but the central site ...
I remember reading something on CCO that said that DLSW+ could be used for bridging other protocols via DLSW suchs a DEC LAT / MOP etc. The example would be to have a E0 on localrouter configured with Bridge Group 1 with Protcol ieee and assigned the...
Within the framework of a project, I need some lights on this subject. Today, I have a connection between my 3745 and one ICA I would like to remove this 3745 and to replace it by a bond series on my router. Thissolution is it possible and which are ...
Hi,i have 2 routers cisco 7206vxr(NPE400) with ios c7200-a3js-mz.121-5.T12.bin , and causally the routers doesn't work correctly.Before i thinked there was a problem with the buffers and i made tuning :buffers small permanent 200buffers small max-fre...
I installed a new 3475 router and setup DSLW peers to the remote sites, and I found my self removing the peers becasue it slowed down the links to a crawl.Once I removed the Peers communications speeds were restored to normal, any ideas?
We have an SNA server on Ethernet and it cannot talk to a token ring device Q159462 from microsoft suggests to disable LLC local Acknowledgement.Does anyone have any suggestions and how can I disable LLC?
I input the following configuration on a CPE router:dlsw local-peer peer-id <address>dlsw timer explorer-wait-time 100dlsw load-balance circuit-countdlsw remote-peer 0 tcp <address1> cost 1 circuit-weight 10dlsw remote-peer 0 tcp <address2> cost 1 ci...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2025 02:34 PM | ||
12-30-2024 06:35 AM | ||
10-07-2024 09:53 AM | ||
07-05-2024 09:53 AM | ||
07-04-2024 06:52 AM |