I am setting up FCOE on the N5K and the server team is asking if we can assign 2 different VSANS on the same interface. So I have a single VFC bound to an interface, now can I assign 2 differen vsans to that vfc?
Hi,
I have two CISCO MDS 9148 switches, Now i want to make it as redundant switches. For that configured with below settings
on SW01:
created vsan(300), Assign the interface fc1/1 to vsan.
created zone(serverzone), added pwwn number of server1_cont...
After more than one year of running without problems, customer suddenly sees this command failing ? any known defect ? (SAN of MDS and N5k)
SWS-01# copy running-config startup-config fabric
This will save the running configuration on all switches in ...
HELLO guys,
I have one question regarding configure dell storage with Cisco MDS 9500 , that I plan to configure NPIV from dell storage and configure F port from MDS , but unfortunately the NPIV port that was created from storage not come up with MDS...
Hi
I would like to restart the supervisors on my Nexus 7Ks and as I have not done this before, just trying to see if anyone has done this before and if I will be following the correct process.
So I have 2 x Nexus 7Ks each with dual SUP2 supervisors. ...
We are looking into installing DCNM7.2 and in the prerequisites it refers to requiring two port groups: "The host machine is installed with ESXi and two port groups are created—one for EFM network and the other for DCNM Management network."
What is ...
Hello,
i have a query, although I may know the answer but still need to be sure.Is the topology as shown below and in diagram supported for initiator 1 to communicate to the target?Logically { [initiator1]---[cN7K-storage NPIV]---[cN5K NPV]---[MDS NP...
Hello!
I had to replace one switch in my infrastructure to new one. After that in DCNM i can see the old switch and new but all VSANs are segmented because the old switch is in network map without any connection. Is it possible to remove the old swi...
Hi
After read a lot of documentation I am very confuse and it is very difficult for me make a picture on my head of how this work.
For example. I have an Array Storage, 2 MDS 9148 and 3 Serves (standalone, not blades) with 2 HBA each. Each HBA has ...
Hi,
I'm facing an issue which doesn't happen all the time and I'm unable to determine the exact condition.
I'm trying to activate the following zoneset:
zone name vsan_200 vsan 200
member pwwn 20:00:00:25:b5:c0:ff:ee
member pwwn 20:00:00:25:b...
Hello all,
we're planning to implement VRFs on our 3548s but the documentation is quite confusing about what features are in the base license and what's in the Entreprise license when it comes to VRFs and VRF-lite. The base license supports VRFs but...
Dear all relavant team or expert One of our customer had IDC center and they are installed N7K 50 device and running about 2 years over now.However, recently that N7K device Supervisor ( sup2) has beeen failed message occurred as a below with differe...
I'm looking to setup a pair of MDS 9148S switches in a high available configuration. I came across a post on the forums, where someone stated you won't trunk the switches, that you would simply create two separate fabrics. Servers and SAN(in our ca...
Hi,
My N5K is configured with a Zoneset with multiple zone. Currently we have issue in one server and we are changing the Network adapter, so I am updating the wwnn and fcid number and activating the zoneset again.
My question in while activating ...
Hello,
I have 3 9148 mds, when I connect this to my MDS-9148-01 to the port fc1/10 I have no issue , if I connect this to my MDS-9148-02 to the port fc1/10 I get the following error. I checked and the ports have the same config.
2000 Oct 17 14:42:23...
