Switches - Small Business

As per the documentation Cisco switch model SG350X-48P has 4 x 10 Gigabit Ethernet fiber uplinks. Can we use the 1 Gig fiber SFPs in these 10 Gig fiber uplink slots? We have a requirement where we need to use this model and connect it to uplink switc...

Hi All,   We are trying to implement dot1x on our SG300 switches. We where able to implement dynamic vlan assignment but we try to implement some extra commands for specific type of devices. On catalyst we would implement this by using auto smartport...

We have a a few SG350X series switches with DHCP, DHCP Snooping and IP Source Guard enabled running OS version 2.3.5.63   The "Backup Database" box is ticked under DHCP Snooping Properties, however it doesn't look like this is working as expected... ...

For some reason neither Administration -> Locate Device nor "system light" in the CLI work on the SG350XG-24F. I also have a SG350XG-2F10 and SG250X-48P and it works fine on both of them.   I'm running firmware version 2.3.5.63. Does anyone know if t...

Hi Can anyone confirm is MFEFX1 (100BASE-FX) the correct SFP compatible with SG300-10SFP small business switch, to support 100Mb MM fibre 1310 nm wavelength, support up to 2 km? The MFEFX1 quick start guide document does not list this switch as comp...

Hello Team, I have a 10 Mbps download and 10 Mbps upload T1 link, that is connect to Cisco 1941 and 1941 is connected to 3 Cisco SF 300 switches. all 4 devices are in L3 mode. In my network couple of users download heavy files from the internet and i...

Hi, What stack unit mode should I set my switches in? I have 1xSG500x and 2sSG550x. The directions on the guide aren't completely clear to me. From my understanding, I will not be able to use a native stack because one of them are a SG500x, while th...

I've been using the SD2005 for a while now.  Nothing physically has changed as far as cabling.  No new hardware has been added.   I'm unaware of any software auto update, but it's possible that the connection that's causing the problem has auto updat...

Hello All I have SG300 Switch and i use it as L3 (Core switch) ,There are 12 switch is connected to it.   I have 3 Vlans   My problem is i got a message (%ARPARPTBL: ARP Table Overflow, aggregated (9)   My TCAM   IPV4 Routing      in use 128 IPV4 Rou...

Is it possible to add Transceivers (SFP)  MGBLX1 (1000Mbps Singlemode) into a SG350XG-24F-K9-AR, even if all poprts of the switch are 10G Ports? Thanks & regards

Hi everyone,   I have a SG500-52 switch that I inadvertently shut off power to the other day.  When I restored power, the switch did not boot correctly so I connected to the console port.  On boot, the switch displayed the following message: The MAC ...

We have several APs connected to this Sw and after a reboot only start some AP Firmware Version: 1.4.5.02 PID VID:SF200-24FP V05      

Hi, I got a problem with 2x SG220 50p POE, actually I can't get the CPU load from snmpwalk with the OID: ".1.3.6.1.4.1.9.6.1.101.1.9.0 ". Any advice? The FW is the latest available. THXIA

Trying to configure newly purchased sg350 switches. The one I am now working on has the most current firmware version 2.3.5.63 and the timeout set to never but every time I go to a different section of the UI, I must log in again. How to fix this??