Switches - Small Business

Elevate your network performance with our selection of switches specifically designed for small businesses. Supported model families: CBS, SG, SF, SX
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Forum Posts

We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...

CoreyP319 by Cisco Employee
  • 2476 Views
  • 1 replies
  • 0 Helpful votes

  (Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful.  Catalyst 1200 & 1300 Hardware Install...

CoreyP319 by Cisco Employee
  • 3964 Views
  • 1 replies
  • 16 Helpful votes

Resolved! SG500X-48P POE

Hi,I am working with a cisco switch SG500X-48P POE, It needs to be use as inter-vlan. but every time that I create a vlan and try to assign an ip address to it. The http and telnet conctivity is lost. I have wait for a long time but the access to it ...

I have unmanagaed and managed switches and I am trying to get a few VLANs set up.In question is VLAN 7 (10.0.6.0), default is VLAN 1 (10.0.0.0)VLAN 7 includes our surveillance equipmentDevices on VLAN 7POE unmanaged switch with cameras patched to HP ...

jklawlor5 by Beginner
  • 290 Views
  • 0 replies
  • 0 Helpful votes

Hello there, Would it be any specific reason why SG500 switch would not accept a proper Cisco SFP copper module (GLC-T). The only log line that I can see is :  %NSFP-I-SFPGibicDetected: gi1/27 SFP port is present      But even if there is apparently ...

Hi, once i rebooted my Smart Switch Cisco SG-200-50 i cannot access by Webmail, my network is working but the switch IP is not answer me (Destination host is unreachable) and it doesn't have Console port, how can i fix this problem?I am new with Cisc...

Hello, we've two Cisco SG220 Switches. One with Firmware 1.0.0.17 and one with firmware 1.0.0.18. On both SG200 we have the problem, that the config save is alway blinking.When i confirm the running config to the startup config, it says done and blin...

a.flint by Beginner
  • 910 Views
  • 3 replies
  • 0 Helpful votes

I have a SG300-10 that is booting to Marvell U-Boot and then into a testing mode. Is there anyway to recover from this? I have not been able to find anything helpful online.         __  __                      _ _        |  \/  | __ _ _ ____   _____|...

Gate Swan by Beginner
  • 739 Views
  • 1 replies
  • 0 Helpful votes

Hi all,   I am a new beginner about optic connection. I am trying to add MGBSX to our SG200-26FP switch, but have some questions.Now I don't connect it to other switch.1. How to know if the module works. I plug in G26, is the ACT light suppose on or ...

lkhsu3275 by Beginner
  • 318 Views
  • 1 replies
  • 0 Helpful votes

Good morning,what is maximum length between the switches for stacking ?In this case there are 4 SG500X-24P-K9-G5 in two different rooms. Cablelength ist about 450m.Is it possible to stack all 4 switches with SFP-10G-LR Gbics. Thanks Boris