We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Goodday friends,I just found a SGE2000P switch with PoE and when i try to access it through a webbrowser i just get a blue screen. See below:I have tried different browsers, refreshed it multiple times and reset the switch multiple times also. what e...
Hello,the Cisco CBS250 series is a plague.Now, I have anther problem that I couldn´t solve.I have a working output ACL assigned to a port where a camera is connected. Works so far good, until I reboot the camera.The whole traffic is blocked by the sw...
Resolved! CBS250 - ACL drives me crazy :(
Hello,maybe I am blind because I can´t find my mistake about my ACLs on the CBS250.My environment looks like:1. PC with IP: 192.168.178.38 connect on dsl-router2. Camera with IP: 192.168.178.122 connected on CBS250 gi24 Only PC should be able to acce...
Resolved! CBS 250 - no private VLAN support?
Hello,I am now a bit confused about the private VLAN support for Cisco CBS250 series. I got some of the 250-8T and 250-24T and I could not find the private VLAN configuration as descripted in this document:https://www.cisco.com/c/en/us/td/docs/switch...
Hi folks,Trying to use radius authentication for mac addresses. First it seems ok, at first plug, supplicant is correctly authenticated10-Feb-2022 16:54:28 %SEC-I-SUPPLICANTAUTHORIZED: MAC 24:5e:be:xx:xx:xx is authorized on port gi2/0/14 But if unplu...
Having recently had a run in with General and Trunk modes on an SG500X I was looking for the difference between General and Trunk modes and found this explanation:General mode allows multiple untagged vlans and also multiple tagged vlans to exist on...
Is the Cisco model SX550X-16FT a POE switch? I checked the datasheet in this link Cisco 550X Series Stackable Managed Switches Data Sheet - Cisco The confusing part is in the summary heading "Power over Ethernet Plus (PoE+) and 60W PoE", it states.....
I recently replaced a series of Linksys SE30XX with Cisco SG110XX switches. I've noticed an interesting issue that I cannot isolate. The main router is a Linksys LRT214 (1Gbps WAN link) and I have a single SG11016 and several SG110D08 attached. Any d...
Hello, I have created several VLANs with my new cbs350 without problems. I configured what port belongs to what VLAN.Now I want to define also MAC based VLAN groups. So for example if I connect a device with MAC-address X it is connected to VLAN 1 an...
I have a strange problem while using MAC based VLANs on a CBS350.I have two VLANs (100 and 400) each running DHCP servers (with router on 10.20.30.1 and 10.20.40.1).Where I have access ports on 100 and 400 all is as expected. Both VLANs give my clie...
Hi everyone, I have a few Cisco SG220 switches which I am trying to query through SNMP.Specifically, I am trying to get the dot1dTpFdbTable from the bridge-mib. I know that bridge-mib uses community string indexing using the community@vlanId format t...
Ciao, avrei bisogno di un modello di switch che permetta di impostare fino a 1024 ACE per una singola porta.Quale modello devo acquistare? grazie massimo s.
Resolved! Visio Stencil for CBS350-48T-4X
I am looking for a visio stencil for CBS350-48T-4X. It does not appear in the small business section of the stencil site. Any assistance is greatly appreciated.
Hello: i have a group of devices with static ips. I would like the switch to allow communication between the devices but not allow them access outside the switch with the rest of the network. Does anyone know the gui or cli commands to make this work...
To maximize bandwidth I would like to create a nic team on my Esxi 6. Given this is not part virtual distributed switch LACP is not supported on the Esxi side. Route based on IP hash is - and I assume this would handle traffic to my advantageHoweve...
