We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board from June 18th - July 18th. These dates are subject to change pending progress. This in...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
I called the small business toll free phone number and gave them the serial number of the defective switch. They told me, based on the serial number, that I didn't by it from an authorized partner so it wouldn't be covered under warranty. I offered t...
Hi, CURRENT SET-UPI have the Cisco Small Business switch CBS250-8PP-E-2G. The switch delivers power-over-the ethernet to two Cisco Small Business 240AC Access Points. I have disabled Smart Ports and Energy Efficient Network. USE CASENice to have feat...
CISCO SWITCH 16x2 GIG NON-POE SWITCH SINCE LAST 15 DAYS NOT GETTING POWER ON.CISCO SWITCH DETAILS:- MODEL-WS-C290L-16TS-LL V02S/N:- CMMWG00ARBMAC:- CC:7F:75:82:69:00
If the left Orange light comes on for 10-20 seconds every 30-40 seconds when the connected device is off what does it mean? The right light is off all the time as it is probably a 10/100 connection.
Resolved! SG110 LEDs
We recently purchased some Cisco SG110-08 unmanaged eight-port switches. I have a dumb question to ask (which is not addressed in the skimpy "Quick Start Guide," unfortunately). My question involves the LED lights. There are two LED indicators on ...
I am trying to configure some SNMP settings on my SF350-48MP switch but I get the error '% Wrong number of parameters or invalid range, size or characters entered'. The command is shown below: snmp-server enable traps mac-notification changesnmp-ser...
Hello,I am new here and need help creating a default route. I have a SG350 configured as follows:I created 6 vlan and assigned them to ports (access/trunk etcIPv4 static routes).Then under IPv4 Interface I set IPv4 routing to enable and assigned IP a...
Resolved! Unable to connect via SSH
Hi Was wondering if anyone has ever experienced or got any suggestions regarding an issue connecting to a SF300-24 switch running v1.4.11.2?Issue is that we have been happily connecting via SSH using RADIUS auth for sometime but we are now getting "...
Hello. I have a network like diagram below.I have to Vlans. Vlan 40 for IP phones and Vlan 190 for pc.In the first switch, there is no problem and the pc acquires the IP address without any problem.But, in the second switch the pc gets an APIPA.Can a...
Greetings,I need the CE declaration of conformity of the SG350X 48 port switch, or just SG350 series switches.I tried searching the site but I couldn't find it.Could anyone provide me with the DoC file or point out where I can find it?Thanks in advan...
Resolved! CISCO CBS220-24T-4G EOL or not
Good Morning ColleaguesI hope you are doing good and safe. May i know if CISCO CBS220-24T-4G has been announced to be EOL or EOS ? Also may i know when this product launched or start produced by CISCO ? Best Regards
Hello, I have Cisco SF300-48pp switch. The switch has only default VLAN and is used so far as simple access switch. I connected a Camera recorder, but the camera recorder's IP is different. I need to have access from my subnet to the camera recorder....
I recently bought a Cisco SG300-10 switch off eBay used. It is perfectly working, my laptop is plugged into it, with my router plugged into another port. It works completely fine. But, when I try to use a serial console connection on the console port...
I have some CBS250-24PP-4G-EU Switches (12 pcs.) and some CBS250-8PP-2G-EU Switches (6 pcs.)I get lost pings on each of the devices on some ports, at random times. I checked it with different ping tools for some weeks.Now I changed one switch, who ge...
I'm trying to use the DHCP relay feature, with no success. I've already tried on a SG300, on a SG350X and now on a CBS350, so clearly I'm letting something pass.Today I have the CBS350 in my lab. It's connected to the network (port 2, connected to an...
