We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Having issues where pair of my Ruckus R610 APs is not getting required power to operate at its full capacity. I need explanation on the SG350 series per port power consumption vs consumed power. Per my pictures attached, 7 APs use 5.5 watts each. Tot...
I can't seem to find the default ip address to configure my Switches SG110-24 & SF100-24 and make vlan on them ?
Hello,yesterday I bought used Cisco SG300-10 for home using.I found some problems. 1. console cable doesn't work, don't understand why so I enabled SSH via webui, connecting to ssh now2. I can't upgrade firmware.The very first of all I downloadedhttp...
Resolved! SG350-10P inter-VLAN routing
Hi all, I am new one here and I am a beginner of IT skills. Sorry If I started the topic which maybe was disscued.I wolud like to ask you where I do a mistake or what's wrong with my switch. Tried to set up inter-VLAN routing in my switch but witho...
I am trying to get my Sg300-28 to work as L3 and intervlan routing except for VLAN22 which I want isolated. .I think I have this correct as defined below except that VLAN22 is not isolated I only give VLAN22 access to the internet but not the other d...
Hi All,I`d have a question regarding VLANs. I`m still struggeling to clearly understand to correlation betwen layer 2 VLAN and layer 3 VLAN. I guess I know the difference, however having problem when seeing them both in operation at the same time. Fo...
Up until 2 days ago, I had no issue connecting to my management port via telnet and then without any change to it's config, one day it just stopped being accessible. I cleared the entire switch config and set it up again but with no success. I can ...
We just bought around 160 Cisco SG350's and I can only login to them using a console cable. This would be fine if I just had one but I don't want to have to do this 160 times. I can't login with the default credentials through SSH (Putty) or a web ...
SG200-50 fw: 1.4.9.4 I am currently monitoring the interface utilization of a certain server down to client PC.The network connection looks like this.Server ----- Server Sw ---- Core Sw ---- Distri Switch ---- Access Sw -- Client PC Issue:The Tx/Rx U...
I need some help making sure my three Cisco SG300-10 L3 switches are configured correctly for inter vlan and interswitch L3 routing on my network. I have a relatively simple setup with two goals – improve network speed (use L3) and **I need to isol...
I am working to move all devices on our network off of the default VLAN (VLAN 1). This address space is 192.168.0.0/xxI am using a variety of Cisco SG300\350\500 switches in Layer 2 mode. All switches still have VLAN 1 as native All switches ...
I have a SG110-24HP switch. According to the specs it has 24 Ethernet ports plus 2 SFP ports. => Is that 100% true? Or is it (as I suspect) that the 2 SFP ports are wired in parallel with two of the RJ45 Ethernet ports?
Hi - I have a couple of VLANs defined on my router (a CISCO 800 series ISR) and a hierarchy of SG300 switches to handle the traffic between clients. For the most part all is working fine, except that the SG300 switches seem to quite happily pass all ...
Hello,I have a SG300-28 that does not boot full, it get stuck in a loop. I connected via console and updated to the latest firmware, see attached file. I have also tried 1.1, 1.2 and 1.4 releases of the firmware. The error:02-Dec-2019 00:24:26 %SYSLO...
Recently imported a SSL certificate (*.domain.tld) to a SG300 Switch. Worked fine, certificates shows up with the correct name in the SSL Server Key Table (Security - SSL Server - SSL Server Authentication Settings). But when i enter the URL https://...
