Greetings,I have to replace/change the WS-C2960S-24TS-L.https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-2960-series-switches/eos-eol-notice-c51-733348.htmlIt is telling to use WS-C2960X-24TS-L.https://www.cisco.com/c/en/us/product...
When we connect LAN core to WAN via Fa0/0 then we assign Vlan to Fa0/0 of Lan CORE at access mode and then we run ospf between LAN core and WANBut we can assign IP to interface of both LAN core & WAN so why we assign IP via SVI?ANY reason
I have two 6807-XL chassis in vss. i run stastic routes for routing. and i want to configure NSF Feature in chassis for no delay in my network. is there any possibility to configure NSF with Static routes.
Hi, I need to monitioring client by AP count on PRTG but I didnt find MIB file. How can I import this data ? Thank you, Yasin
HI Folks, I need to connect two of my nexus 9k switches to cisco 9600 chassis switch which have two line cards with it.can any body help to resolve my doubt. i have attcahed my connectivity and configuration below i have the below configuration N...
Hi,I have two switches, one 3550 and a 3750, wich are connected using single mode fiber. The link works well with a basic configuration: switchport trunk encapsulation islswitchport mode trunkbut when I activate a full trunk configuration as follows:...
Hello, After giving up on trying to get this or any C9300 (I have tried on 3) to go into configuration and trying everything posted here in the forum. I decided to try loading the IOS FUJI 16.9.3 firmware and performed a factory reset all accordin...
Hello,I tried the steps mentioned in the links below:http://www.cisco.com/en/US/products/hw/switches/ps663/products_password_recovery09186a00800945f7.shtmlhttp://www-tss.cisco.com/eservice/compass/common/activities/password_1700.htmhttp://www-tss.cis...
Hi,On a Cisco 7600 with SUP720-3BXL the password recovery procedure doesn't work.In rommon I try to use the configuration Register to boot without password and without configuration load but nothing... The router still ask me login/password for conso...
I have a IE3400 FT switch that I cannot find a sure fire way to determine the config save status. I have looked at comparing the timeticks stored in MIB ccmHistoryRunningLastChanged to ccmHistoryStartupLastChanged, I even tried using ccmHistoryRunnin...
The senior IT person for our company recently passed away from, wait for it, COVID-19. I have been tasked with taking over. I am the network and hardware guy but I didn't handle any of the Cicso we have. I don't have a lot of experience with it but I...
Dear Sir, Model: SF300-24P 24-Port 10/100 PoE Managed Switch with Gigabit Uplinks: What is minimum load to be provided, to fulfill the MPS (maintain power signature of POE)? Rgds.
hello mates,I can't fully understand one point with route-maps:if we have a route map that it contains this statement:route-map fred deny 10match ip address oneand the access-list named "one" is only denying routes.So routes in ACL "one" will be perm...
Hello all,Few of our branch office switches are running with high memory utilization, we are receiving alerts on our monitoring tool for the same. Monitoring tool shows Memory 1 is running with 90% (above threshold limit) and other memory is fine. Th...
Guys, Need some input. Does anyone know if this model SFP will work with Cisco 3850/4500X switches? HP JD092Bhttps://h20195.www2.hpe.com/v2/default.aspx?cc=id&lc=en&oid=4179912 Thanks in advance!
