Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Dears,I m proposing 350X switch for the small business organization, but i m confused with the poe allocation, according to the table below, as it is mentioned in the table below, 382 W power supply can provide power to 32 no's of POE /POE+ ports and...

POE.JPG
adamgibs7 by Level 6
  • 405 Views
  • 2 replies
  • 0 Helpful votes

Hello, I'm working on old switches Cisco CE500, I know we can configure it with 2 manners, GUI and GUI CLI.For GUI CLI I've seen the "write" command, and I beleive we can "wr" the config we make with GUI CLI like that, like if we were working on a "r...

Clem58 by Level 3
  • 622 Views
  • 2 replies
  • 0 Helpful votes

Hi There, We have few VLANs span across 2 cisco 3750 switches.  Switch1 and Switch2.  Configuration for both the switches is attached.  VLANs across switches is accessible with the following issues. 1. The switch 2 can not ping VLAN Interface IP of s...

Hey, i have a problem with my Cisco device (Catalyst 3560G 48Port PoE).I cant ping the switch or ping a Client(Pc). I added the Config and removed all private informations. test-sw-1#sh ruBuilding configuration... Current configuration : 4192 bytes!v...

Play Time by Level 1
  • 697 Views
  • 8 replies
  • 0 Helpful votes

I have an 1841 router and it gets stuck, i'm hoping someone can help me fix this as i think its a corrupt cookie:System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 2004 by cisc...

Hi Experts,Is it possible to convert a L2 interface to L3 interface????Today i tried to configure IP address in 1811router. Interface fa6. But it showed some error as "L2 interface is ot able to configure an IP address." I have enable "ip routing" in...

vipinrajrc by Level 3
  • 24177 Views
  • 7 replies
  • 0 Helpful votes

Hi,We've used IE2000 switches in one of our project network. Customer requirement calls for blocking of any unused ports. Does this switch have any web interface or we need Configuration Engine or Professional software to block the ports?

Javed_S by Level 1
  • 433 Views
  • 1 replies
  • 0 Helpful votes

Anyone face this error before? I have a pair of N5K connecting to 1 pair of FW. FW acts as my ntp server.N5K also connect to a few N2KOur config is:ntp server x.x.x.x use-vrf managementntp source-interface mgmt 0 Strange thing is SAN switch connected...

kevinang74 by Level 1
  • 1027 Views
  • 10 replies
  • 0 Helpful votes

We are planning to connect 2 stacked Catalyst 9300 to a Nutanix Cluster.  While doing research I found a document recommending the Nexus 9300 and specifying that the Catalyst 9300 wouldn't meet requirements for the Data Center.  There was no reasonin...

iwarn2019 by Level 1
  • 1960 Views
  • 6 replies
  • 0 Helpful votes

I recently upgraded my IE2000 switches to the "crypto" version of firmware [15.2(6)E2a Crypto UNIVERSAL] now I receive an error either by connecting through https or ssh that there is an invalid key length. It appears that the switch needs to have a ...

mem16421 by Level 1
  • 2793 Views
  • 3 replies
  • 5 Helpful votes