Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Dear Community, I have a 4510R+E that is utilizing 2x Sup 7E. When attempting to use SSO as the desired redundancy mode, I am able to configure it but the Modules state they are operating in RPR, which is obviously quite inferior to SSO. I have attem...

Craddockc by Level 3
  • 845 Views
  • 5 replies
  • 0 Helpful votes

Dear Community, I have a 4510R+E that is utilizing 2x Sup 7E. The sups are currently running a very old IOS XE version  03.02.05.SG and ROM version 15.0(1r)SG5. When attempting to upgrade to 03.08.06E I noticed that the supervisors would not see each...

Craddockc by Level 3
  • 957 Views
  • 4 replies
  • 0 Helpful votes

Dear All,Two days back my entire network was behaving in unusual ways.When is connect to core switc(4506e) through console, i found following -00:06:51: %C4K_EBM-4-HOSTFLAPPING: Host 02:26:9E:DA:E9:C3 in vlan 1000 is flapping between port Gi4/3 and p...

Hi all,   Been searching the forum but had no luck on finding answer...  I have a SG500-52 switch that I need to configure for Inter VLAN routing. I have 3 vlans: vlan database vlan 100,110,120 exit and the following ip scheme: interface vlan 100 na...

verdura by Level 1
  • 2082 Views
  • 2 replies
  • 0 Helpful votes

I want to access my switch from my office through telnet but i cannot below check the configuration please check what should i do to access it back    RSK-CTRBUD-AS01(config)#exitRSK-CTRBUD-AS01#shOct 24 11:20:55.619: %SYS-5-CONFIG_I: Configured from...

Hi ,   I have ISR 4221, with 2 gigabit Ethernet ports and 1 LTE port. I want to use the LTE port as a back up line, when the cable connect is down. but i cant get it working. Below is a snip of my configuration, what did i miss   chat-script lte "" "...

ermionline by Level 1
  • 4296 Views
  • 23 replies
  • 0 Helpful votes

Hi,   first of all - i already read the incompatibility guide and various documents about VPC and VSS. But I keep having problem with:   Connecting a Campus Distribution 6500 VSS (formaly the Core) to 2 Nexus 7000 (7702) (new core). As the incompatib...

Hello,   Is there any document where EEPROM format of GLC-T is explained? I need this for find out by I2C communication what connector type is in SFP.   Best regards, Patryk

Giteh by Level 1
  • 1090 Views
  • 4 replies
  • 0 Helpful votes

I have a strange issue going on with EIGRP. We have a central site (Cisco 6509e) and several remote sites (Cisco 4500x VSS pairs) connected via AT&T ASE. All sites seem to have their EIGRP set up correctly. It all works for the most part, but we are ...

I'm trying to rollback the IOS-XE version on a 3650 switch. We ran the install to change the code from an Everest version (16.6.2) to Denali 16.3.6, but we have yet to reload the switch to make Denali take effect.   However, I want to back out of tha...

aweise by Level 1
  • 3222 Views
  • 5 replies
  • 0 Helpful votes