Hi all, i am trying to solve the following topology and make vpc with isr router: However isr router gives error: *Mar 2 16:48:17.504: %EC-5-L3DONTBNDL2: Gi0/1 suspended: LACP currently not enabled on the remote port.*Mar 2 16:48:18.676: %EC-5-L3...
Hi, We are in the process of upgrading our core switches, and have gotten two new Aruba/HP 5406R zl2. We previously had only one core switch, and moving towards a solution with more redundancy. The first part is: Is it possible to set up e.g. a d...
Hello Everyone, I have one of 3850-48XS-S. I will configure for our customer. But i saw in the running confing non physical Ten1/1/1-16 interface ports. What are these ports? What does it mean? Thank you. interface GigabitEthernet0/0 vrf forwardi...
Hello, the upgrade/downgrade guide isn't clear about using the install all command when upgrading from 6.2 to 8.1. Only 'cold boot' with this non-issu path described. What happens with BIOS or linecard microcode with cold boot method? Is it really no...
i am not getting access switch login through telnet but i can login through web browser in Cisco sg300-28 switch but telnet service is enable. In switch Telnet Service is enable but i can not login my switch through telnet but i can login in web brow...
Dear all, I just want to verify my design. I am willing to have two Catalyst 2960X to be connected as attached picture. Existing FO already available, it is Multimode 62.5 um and FOPP port type is LC. As per https://www.cisco.com/c/en/us/td/docs/inte...
hello dears,i am looking for a help as i am a little junior ------------------------------------------------Q - The network administrator is asked to configure 113 point-to-point links. Which IP addressing scheme best defines the address range and ...
" Serial 1/0 is up line protocol Down " what is the possible reason for this error ? A. Ensure that the serial cable is correctly plugged in to the interfaces. B. Apply the clock rate 56000 configuration command to the serial0/1 interface of R1. C....
hello i'm nadzir! I want to understand the solution of this problem. I connect nexus 3048tp with 2960s using 1 cable and trunk mode on each interface in 1 same VLAN. in each switch connected 1 pc that access the vlan I mean before. I transfer data us...
In which situation would the use of a static route be appropriate? To configure a route to the first Layer 3 device on the network segment.To configure a route from an ISP router into a corporate network.To configure a route when the administrative...
Topology: Client(DHCP Client:192.168.1.1/24)-----(DHCP Relay:192.168.1.254/24)Gateway----(NAT Inside: 10.1.1.2/30)Outband(NAT Outband:200.1.1.1/30)----ISP Issue: The overload nat can not work fine.the Outband router did not translate 192.168.1.1(DH...
what is ospf Backbone Router ?
Hi, On 2911 router (running as a voice gateway), show run is not giving any output. When we reload the router, its working again. We checked memory, the largest block is much lesser than the free space. Could anyone help how to resolve memory fragm...
Hello Experts - I have to determine whether to use Nexus 5K or 3750 Stackwise Switch for Etherchannel What is the advantage of using Nexus VPC over 3750 stackwise in terms of Etherchannel. What i know is 1) 3750 uses stackwise cable which has cable...
" Serial 1/0 is up line protocol Down " what is the possible reason for this error ? A. Ensure that the serial cable is correctly plugged in to the interfaces.B. Apply the clock rate 56000 configuration command to the serial0/1 interface of R1.C. ...
