Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Greetings, I am trying to configure an ME1200 right out of the box, and some of the most basic commands do not work. For instance when I type in show run I get an error message command not permitted. If I type a question mark I get the following: AC...

Hello I can ping ip 10.10.10.10 but can not ping ip 10.10.10.16 from internet router?! Jeddah#ping 10.10.10.10Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.10.10.10, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), r...

by Not applicable
  • 1381 Views
  • 14 replies
  • 0 Helpful votes

Hi, I'm looking at some diagrams and there are one portion of Tier 2 Network and another portion of Tier 3 Network. Tier 2 Network has L3 switch that is connected with F5, App servers, and firewall.  Tier 3 Network has another L3 switch that is conn...

ohforce55 by Level 1
  • 2378 Views
  • 0 replies
  • 0 Helpful votes

All, I am looking at setting up SNMP v3 traps on my routers and switches. What software is commonly used to collect (and notify) of the SNMP traps from Cisco devices? I cannot seem to find a clear cut answer, or someone saying, "This is the best SNM...

Hi, I have a 4 switch HSRP group with the following HRSP priorities configured on a VLAN.  All switches have a 180 second preempt delay configured. Switch 1 (Active) - Priority 140 Switch 2 (Standby) - Priority 130 Switch 3 (Listening) - Priority 1...

by Not applicable
  • 2961 Views
  • 2 replies
  • 0 Helpful votes

Good day. How can I check LAG interfaces status changing via snmp ? What type of oids I can use for 1) checking joining / unjoining status of interfaces in LAG  2) checking time after last joining. 3) checking LAG mode on interface (lacp/pagp) 4) che...

hatterfix by Level 1
  • 754 Views
  • 1 replies
  • 0 Helpful votes

I was reading one of the slides from this year Cisco Live regarding VPC. One particular slide kinda confused me (attached). My understanding of setting up backup route path with VPC is: Use a dedicated L3 link between the two VPC peers for dynamic ro...

SIMMN by Spotlight
  • 1099 Views
  • 3 replies
  • 0 Helpful votes

Hi All,  I have two questions please, is it possible to advertise networks in BGP with only the 1 - is it possible to advertise networks in BGP with only the ip prefix-list or route-map WITHOUT redistribute or network command? 2 - if I configure BGP...

hi, after configuring MST one of the switches I am not sure why it was showing this when I inserted command "show spann vlan 10" Fa0/19              Mstr FWD 200000    128.21   P2p Bound(PVST) however MST was configured on this switch. when I shut...

Hi, I am facing a issue whereas we have Active/Standby Failover setup - ASA 5555 where as 1. Active Firewall IP : 10.x.x.2542. Standby Firewall IP : 10.x.x.253For this common IP for managing FW is : 10.x.x.1 Rule :User informed that he is not able ...

shahulreg by Level 1
  • 1232 Views
  • 1 replies
  • 0 Helpful votes

My CISCO881W router doesn't boot up. When i connect by console, the only text that appears is the following: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 2009 by cisco...

Resolved! switching

Dears Q-1Suppose i have 100 switches in my network and i try to find out one particular user pc then how i will know that pc is connected to which switch. I have that pc ip address and mac address Q-2 My requirement is my core switch will restart a...

Resolved! Replacing a router

hi  everyone,  One of our clients is changing their Pfsense router, and we're goning to replace it with a cisco.  I've never worked on pfsenses, and the client need to migrate the complete configuration to the cisco. I've uploaded the .xml configurat...

haa by Level 1
  • 713 Views
  • 4 replies
  • 0 Helpful votes