i have 6807XL with sup2T and i have C6800-32P10G line card , i need to now if active only 24 port SFP+ (10G) it will be blocking or not ?
i have 6807XL with sup2T and i have C6800-32P10G line card , i need to now if active only 24 port SFP+ (10G) it will be blocking or not ?
Hi, I have two chassis 6500E switches using VSS feature, and used Sup-2T. we have installed two C6800-16P10G-XL modules in each chassis, My questions are: 1. If I used all 10g ports on C6800-16P10G-XL, it will provide me 160G or 80G. 2. if I used Cha...
All. By reading various sources of document, I can confirm that C6907-XL chassis with SUP2T can support 1) C6800-32P10G and 2) X6724 / X6748-SFP CFC. I would like to know / confirm has anyone have the above actual config running in production? If so...
Hi, I just bough a new Cisco 1921 router to replace with my old Cisco 3660 router. Can any one let me know Cisco 1921 router capable to replace Cisco 3600 router or not? I tried to replaced with 1921, but some how my office internet was down after r...
Hello...can someone explain to me why the last input of this active port shows never. FastEthernet0/6 is up, line protocol is up (connected) Last input never, output 00:00:00, output hang never 9622019 packets output, 740900442 bytes, 0 underruns...
Hello everyone, I am currently trying to set up a network using vlan routing and using the ip helper-address command. I have the vlan routing working if I use the router as the dhcp server but as soon as I want to have my server running dhcp nothin...
I have a cisco WS-C3750-48P (factory default config) that I have connected to a device ( AM335x processor board ) when I try and ping the device from a laptop also connected to the switch I can see the arp request sent to the board and I can see an a...
Hello, Is there a way to load a new .bin file into the flash of a N7K-SUP1 without TFTP or other network file transfer protocols? If so, where can I find this documentation?
HI there, I currently have six cisco switches that need upgrade: Verson 15.2(3)E1, Product ID: WS-C2960X-48FPD-LVerson 15.2(3)E1, Product ID: WS-C2960X-48FPD-LVerson 15.2(3)E1, Product ID: WS-C2960X-48FPD-LVersion 15.2(3)E1, Product ID: WS-C2960X-4...
Hello , We have pair of 6500 in VSS running image 15.1(1)SY1. from last couple of days we are getting below alert in logs . %SNMP-SW1-3-INPUT_QFULL_ERR: Packet dropped due to input queue fullWe have below configration for snmp on the switch snmp-ser...
Hi All,I am facing a packet loss issue for few public ip's of around 40-60%.I have force 10 core router for eBGP peering and below which lies my cisco catalyst C6509-NEB-A. A TenGigabitEthernet connets the two port. Two subinterfaces. I will paste th...
Is anyone successfully running a 6880 with IAs with ISE? (802.1x and MAB) We are having enormous difficulties centered around device tracking.We're on 15.2(1)SY1.Thanks.
i got two ME 3600X and made primary setup on console.now i would like to switch further configuration from network assistant or embedded device manager.http is enabled ip http secure-server as wellon browser i see after logon a short page with some ...
I am looking to upgrade my company swicthes which consist of 29601's and 3750's. When I upgrade the IOS will it have any effect on the existing config or will it just over write the IOS version. Thanks
Hi All, Im getting the error "hardware-3-mcu_i2c_read_error i2c" in my cisco 3750 switch, and not getting the power over the POE switch ports. IOS image is 12.2.(50)SE4. We have rebooted the switch and still POE is not working. kindly suggest if this...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-24-2024 03:44 PM | ||
04-24-2024 02:27 PM | ||
04-24-2024 11:50 AM | ||
04-23-2024 09:53 AM | ||
04-23-2024 02:53 AM |
User | Count |
---|---|
11 | |
10 | |
9 | |
8 | |
6 |