Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

Dear Sir, I am trying to copy IOS image to Cisco 4503-E switch via tftp in ROMMON mode as someone removed image from the flash.when i check rommon commands there is no xmodem or copy commands there.,so i went with tftp.The connection between the swi...

Hi, I have a topology which includes one  multilayer switch and two  routers connected directly to that switch What I am trying to do is I created two SVIs (10 and 20) on switch with ip routing enabled and assigned the two interfaces to which routers...

I am trying to establish inter vlan connectivity between two 3850 switches. I setup a test environment in my private lab as follows Switch 1 VLAN 116 10.1.16.254 (PC1 on this nertwork - 10.1.16.1) VLAN 131 10.1.31.254 (PC2 on this network - 10.1.31....

paramjots by Level 1
  • 6595 Views
  • 16 replies
  • 0 Helpful votes

Hello, I have seen a worring statistic in a couple of Cisco 6500 with VSS. the modules are:   1   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6848-GE-TX       2   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6848-GE-TX       3   48  CEF720 48 po...

j.sarceda by Level 1
  • 956 Views
  • 2 replies
  • 0 Helpful votes

I have 3750-X that seems to be operating but the SYST is out.  The STAT and MAST lights are lit and the ports are blinking normally.  How do I know if the switch is having problems or not?

cwnielsen by Level 1
  • 872 Views
  • 1 replies
  • 0 Helpful votes

Hi All,  I am very new to nexus and need to setup pair of 5k and few 2ks. My question is, do you cable 2x10 gb to one 5k and the same to another 5k thus you have a total forwarding capacity of 40gb ? does nexus load balance across two 5 k or pick ...

cisco8887 by Level 2
  • 310 Views
  • 1 replies
  • 0 Helpful votes

I have two routers, router 1 is in another building far away. ip address is 192.168.0.1 router 2 has the tcl script, ip is 192.168.0.2 I want to send script aa to router 1 's flash, then  run from router 2, ie. tclsh http://192.168.0.1/aa.tcl. may i ...

Mary by Level 1
  • 275 Views
  • 0 replies
  • 0 Helpful votes

UPDATE: According to TAC, it is not yet supported and will be available in 2016 only - this is not really what the datasheet suggested - misled me - by saying "3560CX MACsec hardware capable". )========================================================...

burkir by Level 1
  • 1108 Views
  • 1 replies
  • 0 Helpful votes

Good morning (o; I have two broken 3750E here where switching and stacking won't work... also have them both in the online license tool.... Now the question....do they really have life-time support or not? What would be the cost to open an RMA and...

richard by Level 1
  • 1238 Views
  • 8 replies
  • 0 Helpful votes

Hello All, Below mentioned interface fa 0/48 has been configured as access port and its coonnected to cisco Router (10.69.12.1).only one link is connected from switch to router and there is no redundant link. My question is, switch fa 0/48 has been c...

Shivu b by Level 1
  • 783 Views
  • 5 replies
  • 0 Helpful votes