Switching

Hi Every one, I have tried below command to run auto back-up on cisco IOS router. kron policy-list Backupcli show run | redirect tftp://10.1.1.1/router-Confi.txt   kron occurrence DAILY at 13:44  recurringpolicy-list Backup When I open  ://10.1.1.1/r...

kron occurrence Test-BackUp at 14:00 9 recurring policy-list Test-BackUp! kron policy-list Test-BackUp cli sh run | redirect tftp://192.168.1.11/A.cfg! It copies a 0 kb file. When I tried with  copy running-config tftp: Address or name of remote h...

Is there a way to asymmetrically filter VLANs on a trunk? I am working on an RSPAN implementation for a large layer-2 network, but I am concerned how the RSPAN traffic from any access switch will be flooded onto every trunk link at the distribution s...

Hi,My switch is generating logs stating the same mac in different ways. Do you know why? May 6 17:24:54 2016 Site1 %%10ARP/5/ARP_DUPLICATE_IPADDR_DETECT(l): Detected an IP address conflict. The device with MAC address 001b-4f4f-26ff connected to B...

Hi all, I have my Nexus 5672up and my Fex 2348UPQ, and when I do my basic fex config and I do a show int brief the links are always down. In the logs I get this output command failed: port not compatible [port mode]Nx5k(config-if-range)# 2016 May  ...

I've downloaded c2960x-universalk9-tar.152-2.E4.tar from cisco.com and have placed it on a usbflash drive to be extracted to my switch stack. I've also copied the tar file to flash on the stackmaster. getting the following message when issuing archiv...

hello,I have a system that is experiencing high cpu utilization due to the "Collection proce".  Does anyone have any info about this process?CPU utilization for five seconds: 100%/0%; one minute: 100%; five minutes: 100%PID Runtime(ms)   Invoked     ...

Hi Experts Please have a look at the diagram.  I want to have NAT; translate the 192.x.x.x SCADA and HMI IP addresses to be converted to 10.x.x.x IP addresses before they leave Router 1 and Router 2 to the Switch-TP-Link. What should be the configur...

Hello, I am new to this forum and don't know the rules to post an question. We are using a Cisco 6950 Switch and have around 15 VLAN configured in it. We recently got an UTM to access internet from it and put website filtering and other UTM featur...

Hi Guys, Looking for any document stating difference between HSRP and HSRP+ ? Anyone can help please. Regards, NA

R7 and R6 is connected through f0/1, but in R7, we can't ping to R6 's loopback IP 150.1.0.6, but I can see 150.1.0.6 appear in R7's BGP neighbor. so how to ping R6's loopback R7: interface Loopback0 ip address 150.1.0.7 255.255.255.0!interface FastE...

I have two router connected with F0/0, below is config, my issue is show ip ospf no neighbor, and not able to ping each other, this is in GNS3 R9: interface Loopback0 ip address 150.1.0.9 255.255.255.0!interface FastEthernet0/0 ip address 155.1.0.9 2...

I have enabled below authentication on console 0. Could you please tell which authentication console port will use? Config is as below username SA_PAM_01 privilege 15 secret 5 $1$1RYK$BN8mO.rsxb49/Hpr.sInE/ ! aaa authentication password-prompt "No ne...