Hi Everyone, On EIGRP router configured as stub i need to advertise single static route to eigrp nei.R1 has this configrouter eigrp 650eigrp stub connected summarynetwork 192.168.0.0 This Router is nei to R2.Currently R1 has multiple static routes b...
Hello,I have an ASA 5505 with the security plus licence and a catalyst 3750G. I'm fairly new to this so please bare with me.I want to setup a network with multiple VLANs, some of which can communicate freely with each other, some of which which can o...
Hello, Could you please tell me how i can "decrypt" time-log below in my show logging on a switch 2960 ?SW#Sh logging1y27w: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/19, changed state to up1y27w: %LINEPROTO-5-UPDOWN: Line protocol...
Hi all, I was searching Cisco website for a switch with power and processing redundancy, I found in a CCNP related article that the Catalyst 4500-X supports supervisor/route process redundancy, but when I read its data sheet I couldn't find any m...
hi All, I have a concern with a phone connecting to a port. Port being shut by CDP. Any clue in understanding or alleviating would be of great help.WS-C2960S-48LPS-LIOS: c2960s-universalk9-mz.122-58.SE2.bin !interface GigabitEthernet1/0/46 descriptio...
Hello, Please can someone help me with vrf lite with ospf. I am trying to ping IP's using vrf lite and SVI's. The devices are connected via trunk ports. This configuration works fine when using regular ospf. But for some reason (obviously misconf...
Hello, Kindly, Any one can help me in this command and what is mean route-map Test permit 10 match ip address prefix-list Testt set community XXX : YYY Kind Regards, Tariq.E
We need to set up an LACP Port Channel to connect to an EMC Datamover. What would be the best practice configuration. I have found 2 in my research: Should we use switchport mode trunk or switchport mode access. First:interface Port-channel1 switchp...
Hi Guys I have a core L3 switch, connected up to a HA pair of ASA Firewalls. Now I need to give the asa 2 x inside addresses (active/standby), management IP address and an IP for the firepower module. So I have 2 questions.1) What is the best practic...
Hi Guys, I have an issue with vpc on Nexus 7K. We had a power issue last Sunday on July 5th, as a result I lost one of the 10-GB line card fiber (Module N7K-M132XP-12) on switch 2. What I was expecting in the event we lose one of the 7K switch, we s...
Hi, I'm currently looking for a cisco switch that doesn't need a license? can someone be kind enough to label some models for me thanks. The Switches will be used for hosting game servers non profit
What are the software features on 3750G and 3750-X are needed for the two models to be joined in a stack ?
HiWe have had a layer 2 national Ethernet link installed between 2 of our sites with a circuit presented to us at each site by the ISP. We will be trunking 3 or 4 vlans over it. I am just thinking about the port configs on each end on the switches. S...
Hi dear engineers.I have a cisco3945e router with SPE slot SM-ES3G-16-P swith module connected.SM-ES3G-16-P switch has 18 gigabit ethernet ports (2 uplink and 16 external).Two uplink gigabit ethernet ports of the Switch are connected to the Router in...
Hi I just want to ask a simple questionis there any precautions with native vlan between the Switched infrastructure and the Fabric interconnect ?! I mean can I use any vlan as a native vlan ex.999 "anything but not 1" ?!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-23-2025 01:45 PM | ||
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM |
| User | Count |
|---|---|
| 11 | |
| 11 | |
| 9 | |
| 5 | |
| 4 |
