So I am a bit new to switchport security. I have it working on most of the ports at a location. Its ports where either I have switchport voice and switchport access vlans or just switchport voice vlans. For some reason, those type of ports will go...
The basics are is that I am not getting the speed I thought I would get out of a (qty 4) 1Gb LAG group. I have 2 3750X switches stacked. Across the switches, I have 2 ports from each switch in a 4 member LAG attached to one server. The Server has ...
Hello, I am not clear about logging to remote syslog as it is not working with my setup. Please check the snaphot below and configuration I define: Initial Configuration:- IOU-4 was configure with VLAN-1, VLAN10 and VLAN-11 interface and IP address w...
Hi,Since MAC Address-Based Traffic Blocking does not work with Multicast address(ipv6mcast) , is there a way to achieve the same in another way.If it 's not possible i can do a layer 3 acl (i am already running a acl based on ipv4 address) if i ...
Hello all, I know this has been covered in the past but, im just looking for opinions. We will be upgrading two of our campus distribution switches to 6880-x we will have a total of four each in two VSS. The first campus is small and has about 8 IDF'...
Is it normal for a Cisco 4506, SUP7 series switch to register huge software packet drops at small intervals.While this data was captured no configuration changes were made on the device.Two different results as shown below were taken at an interval o...
Hi, can anyone advise on the ME3400E switches handling of incoming packets that are DSCP marked, using CBWFQ, as to if by default the marking is trusted or if reclassification and re-marking is needed. I have read several blogs that suggest both met...
Hi,I would like to ask how can I route from outside to inside.I'm planning to set-up a Direct access server so the user can access the drive in their home.any Idea about this setup??please see the attached photo.thanks
I'm trying to test the connection to the cloud on GNS using IOU VM. I set the Loopback adapter on W8, with the .137.1 address. GNS 3 recognizes the lo Int on the cloud, I'm able to plug my router to the cloud with the lo interface. I set the ip addre...
Hi Please explain difference between extended vlan and standard vlan.
I have a time clock on the network that keeps triggering up and down alerts in solarwinds. When you do a sh arp on the switch, the device is showing "Incomplete". Other devices on the same 3560 switch, and on the same vlan, are operating normally. ...
Im having trouble capturing RTP VoiP Media with the embedded packet capture feature on an ME3600X. Anyone have similar experience with this? I did an inline capture by creating a SPAN port and the traffic was there. When I utilize the embedded pac...
HiI have 2 sites connected via a Layer 2 circuit. Both sites have a core L3 switch and their own Internet connection. I need to have a virtual server VLAN, that spans across both sites.So instead of using a GW at one site, can i define a GW at both s...
MorningI have a need to restrict data to 95mb of bandwidth and reserve the remaining 5mb for voip traffic per 100mb switch port.There seem to be a number of methods, but what's the best way to do this? I get I would need to match dscp ef to Voice cla...
I have core switch 3560 and 3550 G series switch, can i run intervlan on this switch? I want to design network like. ISP<------------ Core switch /3550./3560<-------Layer 2 switch<-------Client PC For example IP:1.1.1.1 Please s...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-23-2025 01:45 PM | ||
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM |
| User | Count |
|---|---|
| 13 | |
| 11 | |
| 9 | |
| 5 | |
| 4 |
