Hello Team,I have configured the OSPF and trying to configure GRE Tunnel.. I have adversited all the network however it does not show in routing table, also Tunnel is showing in down state and when I run the Show IP OSPF database I see the neighbours...
HelloI know this is overkill but I am more focused on the cheap cost I’ll get it for. Currently I’d only be using it to create 6 vlans, a trunk to my Cisco FPR1010 and of course assigning certain amounts of Interfaces to said vlans.At the end of the ...
We've got a C2960 LSM switch that won't allow traffic that has the 'do not fragment' flag (specifically ssh) to one network. I can ping/traceroute fine, but not ssh. It's a LSM so it doesn'thave command line, so adjusting MSS isn't possible as far ...
Good morning,I am having issues with this C2960S switch. I have everything configured, as far as I can tell, correctly; however I have no routing from my VLAN 2 to the internet. This tells me there is something simple that I am missing. From withi...
Hi,it's been quite a long time since I've got my CCNA, but I got my hands on a ISR4321 to set it up at home and play around with it.Unfortunately I seem to be missing some settings and need some guidance please. I added my current config, so for the ...
Hi all,I have Catalyst 4500 L3 Switch and I am trying to capture packets with EPC on interface TenGigabitEthernet1/3 but I don't see any packets coming. This is the input output rate:5 minute input rate 1394322000 bits/sec, 1530297 packets/sec5 minut...
Hey there i am doing a project for myself. But i get an error: "DHCP failed APIPA is being used". How can i fix this? ThanksPacket Tracer File
Hi,So we have a standalone network for one of departments for Internet/Adsl, Internet-> Cisco 4300 -> cisco 9300now We got 1Gig link from the Isp and I tested the speed directly connecting the Isp Ont device and am able to get almost 1 gig speed, but...
Hello All,I use Cisco 4506E with VSs, is there a command to get logs based on date, for example I want to get logs for the last weekThank You
Hi,I have got 2 cameras on a site on a switch under the same VLAN.The only difference between them is that 1 of them 1 Silvernet wifi connection away from the switch.They are all on the same network as well as the wifi devices. It is all reachable.Th...
Lab 7.4.8 outlines a setup where we need a ArchLinux VM (security_workstation.ova) connecting to a router in packettracer. The goal is to setup a Radius server on th VM, to which aaa authentications from the packettracer will be authenticated.The th...
Hello team, I have a problem here: CORE_HQ to the ISP uses static default route 0.0.0.0, while CORE_HQ to the downlink uses OSPF. When I try to ping ip lo 8.8.8.8 from CORE_HQ to ISP, it is reachable, but when I try to ping from downlink, say Multil...
Hi, We recently upgraded a c9500-48Y4C to 17.9.4a. This upgraded ROMMON to 17.8.1r[FC1]. We are trying to do a factory reset by changing the configuration register value to 0x2142 in ROMMON mode. But we don't see any commands that support it: rommon ...
Hello Team, Will ISSU support on DNAC Version 2.3.3.7-72328-HF5.We tried to upgrade 9407R switches with ISSU its successful. But some switches not successful.I see some cisco documents stating that ISSU not supported on DNAC version 2.3.3.7-72328-HF...
Below configuration is from Nexus, i would like to inquire the equivalent configuration on the Catalyst. object-group ip port NETWORK-PORT10 eq 1039 20 eq 5900 30 eq 5000 40 eq 443 50 eq 6129 60 eq 21 70 eq 22 80 eq 24 90 eq 1024 100 eq 1023 110 eq 1...
