Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi guys,I'm a Cisco noob so please forgive me if I'm asking stupid questions :)I have a Cisco Catalyst 3560 in my lab and it's currently a single VLAN set up with all 48 interfaces in it. The switch receives static IPs from the router and as far as I...

bighostlv by Level 1
  • 1371 Views
  • 6 replies
  • 0 Helpful votes

Hi,reading from CCO: "Ethernet Keepalives:  On broadcast media like an Ethernet,  keepalives are slightly different. Since there are many possible  neighbors on the Ethernet, the keepalive is not designed to determine if  the path to any one particul...

we found one port of etherchannel went into errdisable, the reason is loopback.switch will send keepalive through all interface except uplink and fiber i have two questions1、what is uplink, is trunk port uplink?2、keepalive frame sorce mac address and...

fly by Level 2
  • 282 Views
  • 1 replies
  • 0 Helpful votes

Hi everybody,I´m trying connect two catalyst 3560 Catalyst switch through fiber.  I have a network in the office, it is working. Now, I need to take a switch in my office network (switch A) and add a new switch (switch B) for connect a near office. I...

We have a 4507 switch with two supervisor modules (WS-X45-SUP6L-E) for redundancy and I need I need to replace the standby one due to some issue we experience and Cisco recommends to replace  it. Is there any step bt step  document i can download tha...

gscalia01 by Level 1
  • 3241 Views
  • 3 replies
  • 0 Helpful votes

Hi Everyone Currently studying CCNA. I'm attempting to NAT any machine on an internal interface to an IP address on the wan interface Fast 0/1: 172.25.0.1/24Fast 0/0: 172.26.0.1/24Eth 1/0.18: 172.26.18.1/24Eth 1/0.19: 172.26.19.1/24 There are machine...

Silver_NZ by Level 1
  • 445 Views
  • 2 replies
  • 0 Helpful votes

What is WCCP and how we configure in Cisco Switch 4500 ISO version 12.2(31)SGA8 ? Which ISO version will support to configure WCCP?And Is there any possibility to use Extended Access list or Named access list to configure WCCP.I have Cisco switch 450...

prashant by Level 1
  • 340 Views
  • 1 replies
  • 0 Helpful votes

Hi Folks, I've been out of the networking world for a few years and am slowly getting back into it.One thing that is currently causing me a slight bit of grief is a set of access-lists I'm trying to apply.When planning this I never gave it a second t...

Resolved! Route questions

interface Vlan1 nameif inside security-level 100 ip address 172.16.16.3 255.255.248.0interface Vlan2 nameif outside security-level 0 ip address 172.16.0.3 255.255.248.0 route outside 0.0.0.0 0.0.0.0 172.16.0.1 1route inside 172.16.0.0 255.255.248.0 1...

emrinaldo by Level 1
  • 1213 Views
  • 9 replies
  • 0 Helpful votes

Dear Team. Our system are using 02 switch2960, 02 router2921(EHWIC-4ESG).We have 5 vlan on switch and router, we use HSRP and Spanning-tree. When i plug cable with green color (Fe0/0/0 and Fe0/2/0), The system was loop. IOS c2900-universalk9-mz.SPA.1...

I need to rate limit UDP traffic on a port without affecting other traffic. Would the below work or would this drop all other non-UDP traffic? I could just change the ACL to IP ANY ANY but I would prefer to limit just UDP traffic.  mls qosaccess-list...

ryderse69 by Level 1
  • 2601 Views
  • 2 replies
  • 0 Helpful votes
Unanswered Topics