I intend to uplink NX5020 2 fiber ports to a NX7000 2 fiber ports running port-channel.I have created on both sides:interface port-channel10 switchport mode trunk description NX7000 (SFP) <--> NX5000 (SFP)I have configure fiber interfaces like this...
Getting ready to install new 5000's and they are running 5.1.3.n2 . This seems to be like 2-3 levels behind do most of you try to run the latest versions which is like 6.0.2 version at this point ?
Hello,Is it possible for my Catalyst 2960-s to provide DHCP/NAT service over a single interface? There is no other DHCP server on the network. I am thinking there must be a way to do this, maybe with a VLAN to a specific interface on the switch? I wa...
Hello. I have a large L2 network. We previously had all VLAN STP root and HSRP active on one of two core routers. I recently decided to split the STP and HSRP on both switches to help with processor utilization. I went with the even/odd approach. Thi...
Based on the attached diagram, I need site 2's pc to use site 1's firewall for internet access. If you had 2 factory fresh L3 poe switches, how would you program them to get the needed results?PS anything on the diagram can be changed (ip addreses, G...
Hi!I was checking the specs for the Cisco Catalyst 2960-X Series but could not identify the number of Total switched virtual interfaces (SVIs).What is the number of SVIs on the WS-C2960XR-24TD-I model?Regards,Alvin
Hi,I am trying to configure MACsec between three Nexus M2 ports. once I configure it, my BGP and ISIS neighbors go down.here is the output of my show cts interface all on one of the switches:CTS Information for Interface Ethernet1/1:CTS is enabled, ...
Hi i have attached the topology of my network. I am running eigrp. My question is, access switch a seems to load balancing between links to 3750_A and 3750_B to reach the outside world whereas it should only go through 3750_B since it has 1 gb link, ...
Hello All,I have been trying to trunk multicast data configured under MVR between two Cisco switches.A 3750 switch is the source of two multicast data streams with a 2950 used to output to a receiving unit that will acceptboth multicast data. My sit...
I have a site that my company taken over. It has two HP 5406's being used as cores, with a hodgepodge of HP2510 and other model switches being used as access switches. All the VLANS are terminated on the 5406, using VRRP, with the access switches t...
Hi All,I have encounted an problem that currently has me stumped. I am trying to configure a 3750 switch with ipservices for use as a small localised test bed for wireless. what i am planning to implement is:1 x 3750 PoE switch with 3 vlans1 x WLC1 x...
Hi Guys,i need an advice.im setting up a router as a dhcp server and it is connected to a layer 3 switch do i need to create a subinterface or i just use the default network in layer 3 switch?
HiI`m suddenly having problems with some static routes on a WS-C3750G-12S-E running 12.2(44)SE5.The routing table is really simple, only some static routes and a couple of VRFs. Gateway of last resort is 10.0.224.29 to network 0.0.0.0 10.0.0.0/16 is ...
Hi,What's the method to perform password recover on a stack? I aleady have the standard procedure/link to perform on a single switch. Do I power down both members, disconnect the stack cables, then perform the procedure on the master, then power back...
Hi TeamSuppose that an IP address is assigned to a device, not an interface of the device.How would subnetting be done in this case?Thank you.Unni
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-23-2025 01:45 PM | ||
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM |
| User | Count |
|---|---|
| 13 | |
| 11 | |
| 9 | |
| 5 | |
| 4 |
