Cpu always hitting 70% to 80 % and interrrupt traffic is 70%. Want to know the root cause for this issue. Tech support is attached for your analyze. please help me here. CPU utilization for five seconds: 73%/65%; one minute: 71%; five minutes: 67%P...
Dear all,I have one issue on Vlan in Cisco 3750X switches , I have 2 Offices , I am sitting at corp OFfice and i have one 3750 ( 10.10.1.36)Switch at my location , in my remote office i have one more switch 3750 ( 10.10.33.1) and i am able to access...
Hello,I have the following topology:sw1 - dot1q - sw2 - isl - sw3 and VTP server on sw1.sw2 and sw3 are running in VTP Client Mode. My question here will be.. Switch3 Will learn all the vlans from the server if it is running over diffrent types of ...
Hi Team,We are running virtual TACACS( Cisco ACS), need to check if Centrify is supported on these appliances?We want to install monitoring tool agent on this devices? I meane centtify agent on this device?Please advice is it possible.Regards,Kannan
Hi,I have a cisco 2511 Access server. About 5 days ago the router started showing errors of DRAM memory dump and the server used to reboot about 10-15mins. so i figured it was a error with the DRAM and i replaced the DRAM. Now the error shows as Loca...
Hello,I have a Layer 2 network with more than 10 switches with 7 different VLAN IDs. We plan to install a teleconferrencing system between 4 of the location in the network. I plan to put the related hardware (cameras, videoconferencing terminal etc) ...
Hi,The CPU utilization on my 4510 switch never goes down below 70%. Even during the non office hours the utilzation stood at 68%. I presume this to be very high conisdering there are other switches in my environment which stay at 18% utilization duri...
Hi Team,We want create Local Uasername/password on Nexus 7K & 5K , I am using password 7 but is not taking password 7.Only password 0 or password 5.How to encyrpt my original password to level 5 ( I know level 7 only)?Please send me the link for pass...
Hey!I would like to know how to do the following scenario:SW1,2,3: vlan 10,20,30 and 100(native)SW1,2 have 3 vlan interfaces for vlan routingSW1 vlan interfaces192.168.0.1192.168.1.1192.168.2.1SW2 vlan interfaces192.168.0.2192.168.1.2192.168.2.2vlan1...
Hi everybody.Let suppose we have a video server and some hosts. we want to implement multicasting, So a packet sent by video server is received by all hosts.Let assume we choose the multicast group as 224.7.7.7.My book says all the hosts should be ru...
Hi everybody.How is every one doing?1) How do we configure TTL value on a router's interface?2) Does router consider this value when routing any packet out of the interface or it only considers that value when forwarding multicast packets out of the...
I have spent several days tearing my hair out trying to properly configure our small business switch (SG300-10p) for voice. The phones are a relatively new addition and will replace old POTS phones.Our network consists of a 1941 ISR router, the SG300...
okay, so out of the blue one day (maybe a month ago) i get a call from one of our offices saying all the phones are down (poe phones).i looked on the switch expecting to see a voice vlan missing since are not using vtp, but all of the configurations...
Hi,We are authenticating users and printers via dot1x and MAB towards the ACS 5.1. The ACS then pushes out a VLAN + an access-list. Sometimes printers (MAB) and users (dot1x) end up on the wrong VLAN even though I can see that the correct VLAN is pus...
