Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Dear all,I am trying to implement policing on some ports on a 3560 to limit the amount of bandwidth (e.g. 2M; 8M or 16M) a connected device can send into our network.My problem is that the policy map doesn't police properly. The configured bandwidth ...
I have a 2911 router where I was configuring the device t allow remote desktops connections. Everything is working properly, but for some reason my ACL has disappeared. Has anyone ever experienced this before!?!?!
The module just won't come up. Stays in off-line state. On two identical 5Ks, so its not hardware failure.Have the licenses and running code 5.0(3)N2(2).LAN_BASE_SERVICES_PKG Yes - Unused 11 Jan 2012 -LAN_ENTERPRISE_SERVICES_PKG Yes ...
Hi Matt and Jane,I would like to know why i can't configure to 100 full duplex one port from target follow: WS-X6724-SFPRegards,Ricardo
Hello Experts,I want to block below log message:Nov 3 11:15:30.584 UTC: %SBC-2-MSG-0303-0020-22098A-1584: Socket connect failed: No route to hostRemote address: 00000003 0A0A0102 Remote port: 5060(Debugging info: error code = 265...
Resolved! OSPF: specifying cost
Let's say I have a router A with OSPF and network 10.10.10.0/24 and 10.10.12.0/24 in area 0 to advertise. It has two interfaces connecting to two other routers B and C also in area 0. Router A's connecting interfaces are fa0/1 (to B) and fa0/2 (to ...
Hi,I have a 3550 switch. it has c3550-i9q312-mz.121-14.EA1a.binI am getting the following error-switch is not usable. reason: address bus test failed for associated dataCan anyone help me to resolve the issue.Thanks in advance.
I would like to use a different port to source syslog messages. Can I specify an alternative port other than default? on IOS I think the command is "logging host x.x.x.x transport udp port xxx".
Resolved! Frame Relay - basic question
Hi All,I have 2 routers back-to-back in my lab. I'm trying to configure Frame Relay. For now I'm just trying to ping from 12.1 to 12.2 but it's not working. The serial interfaces on both routers are up and up. And prior to implementting Frame Rel...
i cant resolve one problem in may 1921 isr router, i have a web server in my internal lan , i set up static nat for accessing that web server from outside and it woks fine but i cannot view that site from internal workstations can you suggest me what...
Resolved! CDP neighbors question.
hi: i have a question about CDP neighbors. from the topology below R3 and R2 using same IP addre to connect each other . so when i run "show cdp neighbor" R2 can still discover the R3 . how did R2 discover R3, that does not make much sense here since...
Resolved! ospf and default route 0.0.0.0
Hi there,I have a remote site LAN that is connected via a point to point connection back to our HQ office.I have extended area 0 out to this remote site and the remote L3 switch has formed an ospf neighborship with our HQ L3 switch fine.-------remote...
Resolved! Traceroute output !A * !A
Hi, Quick one.... Getting this output doing a traceroute: Router# trace 172.20.5.51 1 10.1.15.42 0 msec 0 msec 4 msec 2 172.20.10.26 !A * !A Everything is fine. The IP 172.20.5.51 is a loopback of the same device that has the 172.20.10.26 on a...
I have a situation where I have just been provisioned a new T1 line from At&t. They refuse to do multilink ppp on the 1841 router they sent me, and I have another T1 already in place with a managed 1700 series router, again, they refuse to do multil...
Hi all,Can someone tell me the cheap wan router with 3 fast ethernet ports?Thanks
