Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello.Should I configure Dual-Active Fast-hello before or after converting to VSS?Also, I have different routers connected to my two 6500 and so I have different static route. Imagine the following routes:- ip route 0.0.0.0 0.0.0.0 192.168.1.1 (6500-...

jcarvalh by Level 1
  • 1256 Views
  • 1 replies
  • 0 Helpful votes

Hi AllWe have layer 2 extension between the datacenter as given in diagramAre the STP port roles given in the diagram correct ? Im not sure why the priority of both N7k's were given the same (4096).. both the N7k's assume that they are the root bridg...

sblavanya by Level 1
  • 1755 Views
  • 3 replies
  • 0 Helpful votes

We have a DCN (Data Communication Network) for managing Customer End Devices (Flexihybrid Microwave). For past few days we are facing DCN visibilities issues. Our main concern is network availability.All switch have access port with specific VLANs. M...

Hi,I'm looking for a Cisco Network Backbone (so best 2 core switches).At the moment we have 2 6880 Blackdiamonds, where are 20 Switches connected over Optical Fibre Cable to them.Because these 2 Coreswitches are very old now (over 9 years) i'm lookin...

can't get my 3750-48-ps upgraded with IP services. It says it does not support the feature set.  documentation leads me to believe that it should.  Any thoughts?

Hione of my port on N7K-1 is connected to another port on N7K-2, there are many other ports also connected between these chassis, but i am not able to see this particlar port, i have enabled cdp o this port also particularly by issues command cdp ena...

Dear Techs,I am using the following command to bind the mac address to ip for printersip dhcp snooping binding xxxx.xxxx.xxxx vlan xx xxx.xxx.xxx.xxx  interface gig x/x/x   expiry 1000000000(because we have ip dhcp snooping and ip arp inspection on V...

Hi out therewe are running a a redundant set of nexus 5020 nxos 4.2.1 and another set running 5.0.3. They are inter-connected with 2 10GB fiberlinks with 50km's between given a latency of approximately ½ mSec - is there anything special to be aware o...

tiwang by Level 3
  • 2954 Views
  • 16 replies
  • 0 Helpful votes

Hello,Im reading a LAN SWITCH Security book and i have a question regarding this sentence from the book: "a root port should typically be sending many more BPDUs than  it is receiving. The opposite is taking place here, indicating suspicious activity...

from88 by Level 4
  • 1749 Views
  • 1 replies
  • 0 Helpful votes

Right now the HSRP tracking is based on physical status of WAN link. But this is creating issues sometimes because the WAN interface continues to stay up and not learning routes.So, I wanted to you to suggest what to track from the remote office and ...

Resolved! Sup2 OS Conversion

Hello,I am embarking on the fateful journey to convert a SUP2 from CATOS to IOS and from what I have read so far, it's not a an easy process to navigate.  I am ready for the challenge but will gladly accept any tips from those who have already succes...

wpalumbo06 by Level 1
  • 5694 Views
  • 31 replies
  • 0 Helpful votes

Hi all,Is carrier tring to put loop toward Customer site i.e CE is dangerous for customer network. Can there be any problem? We usually ask carrier to put loop toward PE but today my co-worker said putting loop facing CE is dangerous,...it's like hac...

get_rthym by Level 1
  • 1788 Views
  • 4 replies
  • 0 Helpful votes

Hii have cisco WAP4410N access point(which are in vlan 10.10.x.x) connected to cat3750g(10.10.11.x) switch. and this connected to firewall. i couldnt access wireless gateway. tracert gettting failed after reaching the cat3750g.wap.......(vlan)..........