Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

hi dears friend .... i wanted to make VOIP network in my place ,i.e i have 5 SIM  phone card in my place , i whanted the person outside of this place when  need to call to this place pass the call through the voip device and  can record the call and ...

Haven't used router commands in years, so I thought this would be a lot easier in SDM. Rustier than I thought!! Need to create an internal vlan (192.168.1.0) and NAT WAN fe04 with ip that corporate has given us to use (45.245.13.21) to connect to cor...

About DTP, someone knows what happens if I link three interfaces of three different switches with an hub.Cisco says that DTP should be used as a point to point protocol, but in that case is it possible that two ofthe three switches negotiate a trunk ...

Hi,Please see the below pic. there are two Router  R2 and R3.I set the IP on R2 and R3 interface is up but no IP address.R2 Interface Status and PORT. is upR2#show ip interface brief | include upSerial0/0                  1.1.1.1         YES manual u...

abhi-adte by Level 1
  • 9926 Views
  • 9 replies
  • 0 Helpful votes

Hi!I have a Cisco 6006 router that is configured with som subnets as vlan interfaces. And i have connected a Cisco 1812 to the router 6006. I can ping both F0 and F1 interface ip address on Cisco 1812 from 6006 but nor from other vlan interfaces. All...

sfanayei by Level 1
  • 1320 Views
  • 3 replies
  • 0 Helpful votes

Dear sir,I have cisco 6509-E Switch which has (s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(18)SXF9, RELEASE SOFTWARE (fc1))I would like to upgrade with ( (12.2.18-SXF17a Software- s72033-adventerprisek9_wan-mz.122-18.SXF17a.bin)). the...

Hi All,I've configured a Cisco 877 ADSL router with two vlan's. Vlan 1 in the range of 192.168.1.0/24 and Vlan2 in the range of 192.168.2.0/24. I've added the following access list in the inward direction of int vlan1access-list 101 permit ip 192.168...

Please, give a look at this table:trunk – trunk                                      → trunktrunk – access                                     → problemtrunk – dynamic desirable                      → trunktrunk – dynamic auto                        ...

I have a seniro to configure RSPAN to monitor traffic for Web Sencesource is connected to 6509 and destination is connected to 4507R6500 is configured as backbone with VSS configurationand 4500 is used as a server farm both are connected each other v...

Hello!   New to 1710 setup, I have been fighting this for awhile and am getting back to it. One Vlan, everything passes fine with the connections but no internet access from PCs on the Vlan1 side to FA0, to the DSL router <non-Cisco, providers box>. ...

cmedley67 by Level 1
  • 4065 Views
  • 12 replies
  • 0 Helpful votes

I wanted to know in a domain environment if a Layer 3 configuration switch would all workstations still communicate locally even with network outage. The situation is 5 pc's plugged in on layer 3 switch with static IP addresses on each and one pc has...

In the CCNP SWITCH 642-813 Official Certification Guide by Hucaby, about VTP pruning, you can find:"Broadcast and unknown unicast frames on a VLAN are forwarded over a trunk link only if the switch on the receiving end of the trunk has ports in that ...