Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
I need an opinion regarding design for our new VSS layer we are about to implement. The new VSS switches will be connected to our core (two core 7600 routers), looking over design suggestions from Cisco, it appears the best solution for HA connectivi...
Hi, Can anyone point me in the right direction for creating and removing user accounts to access my 2600 router?Many thanks in advance
Resolved! VTP Password
When I set the vtp password on my server switch (apple), then set the same password (apple) on all my client switches it takes a long time for newly created vlans to proprogate down. Is this normal behavoir?Is there a command that will speed up the p...
Can anyone point me to those great Cisco diagrams that map the different traffic classes (voice, bulk data, transactional data etc) to their respective DSCP / COS values to the respective queues and thresholds for each of the switching platforms / mo...
Resolved! ACLs on CAT6500
I am getting strange results while applying ACLs on the Cat6500 Vlans. I am not able to understand the usage and difference between IN/OUT and whether it is used in the same manner.Is Cat6500 ACL similar to Router IOS ACLs or do they work differently...
Resolved! Negate 'crypto pki' lines
all,can someone help me remove these lines on our 2800 router. i believe this was generated when i put the command 'ip http secure-server' and then it generated 1024 bit crypto key.crypto pki trustpoint TP-self-signed-1600565986 enrollment selfsigned...
Hi,Can someone help to understand the use of SUP engine in 6500 switches & why is it only found in these higher end switches and not in others normally.Thanks in advance..
Hi All,Is it possible to track (reachability) or a remote ip/host like in ASA we can track the remote host reachability with sla config.
Hi,If I use two HSRP groups with two routers back up each other in all manners and put the routes in my internal network device to both virtual IPs for the same source subnet, will it send the traffic 50-50 percent to the same IPs (routers).like:HSRP...
Hi guys , I am still new , can anybody help me intrepreting the command . I believe the BGP has been redistributed into OSPF . But what the commands metric-type 1 , means . BGP deterministic-med commands being used , I am not sure , how it works rout...
Resolved! LAN Question
Is it possible to close all of the TCP ports except TCP port 25 (SMTP). We don't want any traffic coming in or out except for outgoing mail. Please let me know how to configure this...
I am looking for how to configure VTP on an C3825 router. The commands to set VTP zone and version are not available. All of my routers are set as servers, but I can't see in the config where I would put them in either transparent or client mode.
I have clients running IGMP version 3. IGMP snooping is enabled on my 2960 switch and the switch is tied to my 1811 router with IGMP v2 enabled. The problem I am experiencing is the multicast traffic does not begin to flow until router does the que...
Helo guys, I tyr to configure NAT for two subnets that I have, I have this commandRouter(config) # access-list 101 permit tcp y.y.y.y 0.0.0.255 host x.x.x.xthen I put the nat outside in host x.x.x.xRouter(config)# int fa0/1Router(config-if)# ip nat o...
I've got a device which requires stacked vlans (q in q/second dot1q). I've got a cisco 7507 as my router, and a 3750G switch. I think I've figured out that I need to combine them at the router level, but I can't find any documentation about how to ...
