Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Does anyone know if the WS-X6748-GE-TX module has MDI/MDI-X support and if so what port speed is it supported at?as always thanks
Resolved! DHCP Relay question
Hello experts,Hope you can help me with this scenario:PC|(NM-16ESW)c2691#1(Fast0/0)|L2_Sw - PCs |(Fast0/0)c2691#2I have a DHCP pool configured in router c2691#2, which leases IP addresses to the PCsattached to L2_Sw. I need to plug a PC on one of th...
I have a pair of 6500 switches with SUP720's and I'm wondering if you have a layer 2 vlan trunked between the two switches and your trying to diagnose Utilization issues:How do you measure that?I know you could look at the port-channel that is trunki...
Hi everyone ,,, I like to say thanx in advance for reading my post and for any reply's..Here is my problem... A friend of mine gave me a AP 1200 that he got along with other things he bought on an auction on ebay... I am a newbie when it comes to thi...
Hi,Currently My CSM is running at bridge mode, but I need some test with router mode (another subnets), can I configure CSM running bridge mode with subnetA, and router mode with subnet B&C? Is anybody has example with router mode that the real serve...
I have a VLan setup in my network of 192.199.1.xxx i have this complete with a port on my ASA 5501 (192.199.1.254) it seems that i can get communitations to the firewall but the firewall is dropping traffic and not allowing any internet traffic to pa...
Resolved! Cisco 4500 - slowing down of LAN
Hi all.At one of our offices connected to our central location over a metroethernet LAN we have a Cisco 4500.Recently we have started experiencing weird slowing downs of network for a few moments.I believe that the problem is in the metroethernet lin...
Resolved! Cisco 2621 behind a DSL modem
I recently bought a cisco 2621 router for my small home based business. My ISP is Embarq DSL. I got the router and modem working together but only as the cable modem doing the NATing. The internet is not very relaiable with this setup. I want to t...
Anyone know the maximum amps that the switch above will use if fully populated with IP phones drawing power?
Hi all,I am seeing quite a high percentage (30%) of my packets being processed switched on a 2611 router. CEF is enabled on all interfaces.Would like to confirm if packets directed to a "secondary" ip address will be processed switched.As a temporary...
I am replacing out a pair of 5500s with 6509s one-at-a-time. Once the first 6509 is replaced, it will be trunked via FEC (FastEtherchannel) to the 5500 until that 5500 can be replaced. I want to verify that my the FEC I plan to use will, in fact, wor...
Baisc configuration done. All the links are UP. Connectivity showing, but hosts are not communicating with basic configuration. New Vlan created and switch port added but same problem.
My telco assigned me an etxented vlan for a metro ethernet deployment. I have no option but to use extended vlans. My routers and remote site hardware have been upgraded and can process extended vlans. My problem is with my sup1a in my central site. ...
I have a router; it is connected to Switch. My pc is conencted to switch and I have to configured as static IP with defaul gateway; 10.10.10.10;Other pc is connected to router FE2; without configured static IP; Default gateway is 10.10.10.1?These pc(...
Hi all, can anyone help me on this issue, I have a surver that connects to a lan, and uses a dial up modem. When the modem dials, the lan connection drops until disconnected, I see that when the modem dials a default route is put in the routing tabl...
