Resolved! Can not ping to my ftp server
Hello I am having trouble pinging to my ftp server and also having trouble getting PC5 and PC6 to pull a ip from dhcpCan anyone help?
Forum Posts
Could anyone confirm whether the Cisco 2960X-48FPS-L does support 2 x 10G uplinks ? The specifications only mention it's a Gigabit switch with ports Gi1/0/49 to Gi1/0/52 only supporting SFP's. However, "sh ver" comes back with 2 Virtual Ethernet int...
Resolved! QoS Policy Counters on Catalyst 9600
Hi guys, Could anyone help me, I have configured a Policy-map on my catalyst 9600 switch but after monitoring the policy using the "show policy-map interface" command no counters provided in configured classes and in class-default also. My Class-Map...
hi all,whats the best way to go about this as atm i have configured the ports connected to the wap like this interface GigabitEthernet6/0/45switchport trunk allowed vlan 11,22switchport mode trunk this works but sometimes i get "heart beat missed" on...
Please provide a BOM for the following please. QtyN9K-C93180YC-EX4SFP-10G-LR=14GLC-LH-SMD=74
Folks, Really excited to be jumping into Packet Tracer. I am in "Introduction to Cisco Packet Tracer", chapter 2, 2.1.1.2 and it says to double click "Deploy Devices.pkt", but I for the life of me can't find it after looking for one whole day. Now t...
Resolved! Configure DHCP Server on Layer 2 Switch
I am working with a network with a topology shown as below.I break the whole network into 3 VLAN, 10 for MANAGER, 20 for DBA and 30 for EMPLOYEEI have checked the connection between the DHCP server to the router and the computers in the same vlan. Ev...
Hi Studying for the CCNA, I'm a bit confused about the definition of the RSTP disabled role I find multiple sources stating that "disabled" means that the port is administratively disabled. However, in the official course guide a few paragraphs later...
Hey noticed that our cbs series switches are auto trunking when connected with other cables even though they are across different vlans. Is there a way to disable this?
Hi,I am preparing a stack with two switches the second switch was a member of another stack. The first switch has all the configurations like SNMP spanning tree, VLAN,I had erased the previous configuration from the second switch except for VLAN .d...
I have the following topology:Default Gateway1 <--> SWITCH1 <--> [ NIC2 - (Windows 10 PC) - NIC1 ] <--> SWITCH2 <--> Default Gateway2 --> InternetNIC1 is DHCP configured, and connects to the internet successfully.NIC2 has a static IP address/subnet m...
Resolved! One way ip dhcp snooping at switch
Hi we have switches connection like this: dhcp server -----(g0/3)switch1(g0/1) ------(g0/2)switch2(g0/4)-----clientYou can see four interfaces are labeled in the diagram above. If we want to add ip dhcp snooping trust, the command have to be added t...
I have a Cisco 3560E-48TS-S switch which I successfully upgraded to: Switch Ports Model SW Version SW Image------ ----- ----- ---------- ----------* 1 54 WS-C3560E-48TD 15.0(1)SE C3560E-UNIVERSALK9-M Can I use this image:Catalyst 3560X-48T-S Switch -...
I need to set 2 options 67, but when I try to set the second one, it overwrites the first option 67. Device: WS-C2960XR-24PD-IVersion: 15.2(7)E4 ip dhcp pool xnetwork X.X.X.X X.X.X.Xdefault-router X.X.X.Xdns-server X.X.X.X X.X.X.Xdomain-name YYYYYYYo...
Hi there, (Switches in question here are C9500-48Y4C (swA) and C9300-24T (swB), both running at version 17.3.3.) I'm trying to get DHCP to work over MPLS/VPLS (which is working very well besides DHCP).I suspect some sort of ip helper is required to g...
