Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
Hello all, Is there an efficient way to create a local admin on multiple cisco switches, instead of having to login to every switch to do so? Can this be done using cisco prime? where you can create a local admin account and push it out to all the sw...
Hello I am seeing an issue with PoE on a switch stack (WS-C3650-48FD-S running 03.06.05E). Issue affects both non Cisco and Cisco devices. Not all switches in the stack are affected by this - each switch has a single PWR-C2-1025WAC PSU and the power ...
hi we need help for Cisco Catalyst 2960X-48FPD-L Whit SFP+ 10GBdoes not boot.we tried to access privilage mode cannot load imagewe access only boot mode but it can not accept new file switch: dir flash:Directory of flash:/ 2 -rwx 34 <date> pnp-tech-t...
Hello,I know this topic has been discussed many times, but I didn't find clear anwer yet. Let's say speed of interface of the swith is 1Gbps. Does it mean that theoretically this interface can transmit and receive data at the time with the speed of 1...
Can I run PVST and VLAN Translation simultaneously? If so which switches support this? Thanks
hi, On a 'show nat' display, what does the untranslate_hits mean as opposed to translate_hits.thanks.
So, I am playing with ISE to do a template to change a PC port to a trunk for an AP. This is working fine except for one issue, when I disconnect the AP the port is retaining the native vlan as the access vlan instead of the original.Before AP:switch...
Okay, so i'm on 92%, but the last 8 remaining procent says that my pc's ip addresses are wrong and my router serial interfaces too. I don't understand why. Here's the assignment: https://assignment.itslearning.com/Annotations/AnnotationApp.aspx?Annot...
Hi Team, We are finding that lldp neighbor entry is visible for the subinterface(vlan interface). how to avoid the lldp neighbor for the subinterface alone? GE0/0/26 TN-RMD-RSM-T3-ST-SBE-... Gi0/0/0.198 104GE0/0/26 TN-RMD-RSM-T3-ST-SBE-... Gi0/0...
Hi,I'm trying to setup an 897 router to share a single DSL (with cellular failover) connection among 3 apartments - each with their own access point and VLAN, along with a single guest wifi network. I can connect to the access point and ping the rout...
Does anybody know if Cisco Catalyst C9500-40X-A ?switch can support 1Gig Rj45 sfp
Hi Team, We have VS-SUP2T-10G supervisor engine on 6500 chasis. All the 10g port on module present in chasis are used. Can we used supervisor engine 10gig port for connecting link of 10 gig
I have a couple N3Ks that I am getting no console output from them and the LED on the front just blinks blue. I have tried re-seating the RAM which has helped in the past with some units that would stop booting, but in this case I am still just getti...
Hello,how can I monitor Interfaces and VLANs in one Monitor Session?Problem is, that this monitored traffic needs to be send to ONE single destination port, what is not allowed to do with 2 seperate monitor sessions.So my general problem is:port 1 ne...
We have a Cisco Catalyst 4510R+E Switch and we want to install 10 Gigabit Ethernet port slots on it. We want to know that how many number of slots can de added to the switch with maximum number of 10 Gigabit Ethernet ports per slot. And what can be t...
