Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

Can a Catalyst 3560G-48PS switch perform well as a distribution switch for a LAN of about 350 users, for intervlan routing between two VLANs, where VLAN1 has 250 users and VLAN2 has 100 users? Would this function overuse the switch capabilities? Woul...

ciscomv79 by Level 1
  • 1419 Views
  • 6 replies
  • 0 Helpful votes

Hi allI am in process of migrating ip addresses over to a new scheme, the pc's are currently in vlan 1 and so is the dhcp server. I am putting them in a new vlan and want the dhcp server to issue the vlan a new ip address scope, they will both need t...

Hi, thanks for your help on this quick and basic question:In order to take advantage of a stack of Catalyst 3750 switches, I should just expect to have two NIC's (Network Adapters) onto my servers? That way I would plug NIC1->Cable1->onto Cat 3750 "b...

news2010a by Level 3
  • 507 Views
  • 1 replies
  • 0 Helpful votes

Hi Guys,I want to clear one doubt, please help on this.Cisco says," Per-Vlan Spanning tree(PVST) is a Cisco properietary version of STP. Due to its proprietary nature, PVST requires the use of Cisco Inter-Switch Link(ISL) trunking encapsulation betwe...

Dear Support,I'm a router QoS person, and am completely lost with Catalyst QoS. Seems to be more wrr/srr rather than class-map and policy-mapAm I missing the point or looking in the wrong place?Can anyone point me to a guide that shows me the syntax ...

aoshea by Level 1
  • 1236 Views
  • 3 replies
  • 0 Helpful votes

Hi,Has anyone heard of this "The IEEE Gigabit Ethernet specification does not allow hard-setting a NIC at 1000Mbps". I'm referring to IEEE sepcification.What happen is I'm configuring this non-Cisco device in between 2 Cisco devices which I hard-code...

Danilo Dy by VIP Alumni
  • 608 Views
  • 2 replies
  • 0 Helpful votes

I have a point to point T1 Serial interface on a router that is in interface UP, line protocol DOWN status. The telco has pointed to the problem being on one side of the link, where do I start looking? The router has DCD, DSR, DTR, RTS and CTS all ...

I'm working on port monitoring on a 4510 switch and I have a slight problem. We're using Callrex voice recording software and have successfully configured the port monitoring on the voice vlan. Everything works great.In a meeting yesterday with our...

|--

good day, I have a problem catalyst 3560 since he himself after several days, it sends a message to me of which it has low memory, does not allow me to access VTY way and no Console way, after some hour does not respond echo to me ICMP and by ultimi ...

Morning, is there any way to tell the approximate age of a switch (mfg. date) ?I can approximate by the datestamp on the IOS but was loking for a beter method ? Thanks, Bud.

Redundant 6509s in network each is set to vtp mode server.As both are vtp servers, if changes are made on one of the 6509s will the chg propogate to the other 6509 vtp server or does it require manual update?Each 6509 is configured for even / odd VLA...

tsrader by Level 1
  • 556 Views
  • 1 replies
  • 0 Helpful votes