Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
The given network is 220.10.20.0/24. Calculate a VLSM subnetting scheme for the above topology and fill in the box with appropriate answer. Note: Hosts shown on topology are usable hosts. Don't use space in your answer.What is the subnet address of L...
A:255.255.240.0B:/14C:11111111.11111111.11111100.00000000D:11111111.11111111.00000000.00000000
Resolved! Labbing Static Route? Packet Tracer
I have setup a static route between a L3 switch and a Route however I cannot ping from my PC's to the router interface I can ping between the two interfaces on the L3 Switch and Router I can ping the interface from my PC's to the switch interface con...
Resolved! C2960X switchport mode trunk
Model: WS-C2960X-48LPS-LOS version: 15.0(2a)EX5VLAN: 10,20Port configuration:!interface GigabitEthernet1/0/52switchport mode trunk! Query1. Is the vlan 10,20 frame can be switched via port52 when only 'switchport mode trunk' configured?Query2. Is por...
A: line telnet 15, password Rm$18, loginB: line v t y 0 15, password Rm$18, loginC: line v t y 0 16, login, password Rm$18 line con 16, login, password Rm$18
Hello.We have multiple vlans on an L3 switch configured with each their subnet, with routing enabled, to make vlans discuss between them.We have disabled ACLs (ACL extended), which was configured on each vlan.My question is whether the broadcast dom...
VLSM is applied on a network topology and three subnets are given as follows.SN 1: 20.20.10.0/26SN 2: 20.20.10.32/28SN 3: 20.20.10.80/30Which of the following statements is true? A: SN1 and SN2 overlaps.B: SN1 and SN3 overlaps.C: SN2 and SN3 overlaps...
Router Branch_R is configured with the following (copied from running-config):!interface GigabitEthernet0/0no ip address!interface GigabitEthernet0/0.5encapsulation dot1Q 5ip address 192.168.5.1 255.255.255.0!interface Serial0/0/0ip address 20.10.10....
A switch is configured with V LAN s 10, 20, 30. Which of the following commands will remove only V LAN 30 from that switch? A:Switch(config-if)# no switch port access v LAN 30B:Switch# delete flash :v LAN. DATC:Switch(config)# no v LAN 30D:Switch(con...
Resolved! Nexux 3k VPC Spanning tree issue
I think I have spanning-tree issues with the Nexus 3k Switches using VPC. The problem we are having is when one of the four switches is rebooted (see diagram), all connections to the other switches go down. Any help would be appreciated.
Resolved! 1
Which of the following command sets will assign vlan 99 to the switch port fa0/24?A. int fa0/24 switchport mode access vlan 99B. switchport fa0/24 vlan 99C. int fa0/24 switchport access vlan 99D. switchport acces...
Hi Experts! I'm planning to get CML Personal version and I've been trying it with a trial version from the DevNet Sandbox.It seems that CML support most of command as actual Cisco devices. 1. How do you connect to CML Personal? (not trial)- Trial ver...
I have two switchs (model WS-C3850-24T), we are trying to monitor their cpu with cactiwe tried many Templates but all of them read the cpu of the first switch correctly but read the cpu of the other one wrongso we tried prtg but got the same resultss...
nexus 3064 vlan Qos limit not working we need data limit from vlan or ip not port limit itspossible ?
