Running version 17.07.01 & looking to update it. I've formatted the USB to FAT32 & copied the new IOS version to it as a .bin file. When I insert the USB to the 9300 switch, the switch doesn't seem to see it. Thoughts?Switch#dir usflash0: ...
Forum Posts
We recently replaced all our switches with 'Catalyst 9300 48N UPOE's -- now certain endpoints (namely Panasonic toughbooks and HP PCs) do not detect when you plug in a network cable unless you use some sort of repeater like an IP phone (which fortuna...
Hi AllI see Cisco are now offering the 9350 series switches, can anyone tell me how these differ from the 9300 line? will these ultimately supercede the 9300 line?cheers
HiI have two cisco catalyst 2960 switchesIn this Switch A, one of the SFP Module port number Gig 0/26 is in Trunk for allowed V Lan 1 with speed 1000 & full duplex & type autoAnd also in the other Switch B, one of the SFP Module port number Gig 0/1...
Good morning,I have very little Cisco experience, just joined a new organization, and was told to learn about the Cisco C9500-24/48Y4C switches. The switches were configured before but the person left and we lost everything. I know the default value...
Hello,I would like to know how to bypass startup configuration for WS-C4510R-E model switches. I am able to access ROMMON. Where do I go from here? Again I need the instructions for WS-C4510R-E specifically as they are different from the WS-C4500s I...
I was told that ETS is supported on the Nexus switches, not Catalyst switches like the C9300. After looking at some ETS config examples on the Internet for Nexus, it looks no different than CBWFQ (or modular QoS) configuration on the C9300. In both...
I have uploaded the EDS file from the switch and added it to my PLC programs IO tree. No matter what choice i select for the connection i get error code 16#0126 Connection Request Error: Invalid configuration size. Has anyone here successfully used a...
Hello,I want to add the following Bash commands on a Nexus switch. Will there be any impact from adding them?Switch(config)# feature bash-shellSwitch(config)# endSwitch # run bashbash-4.4$ cd /mnt/pstore/stats_ssdbash-4.4$ ls -ll Thanks in Advance
Hello Community,we have some issues concerning VRF and MAB that we don't understand.Our Platform is a C9500, network essential smart license.We use the Mgmt-interface gi0/0 for security reasons and a central radius server for authentication, which wo...
Hello Team, FAM!Attached is my high-level topology between DCs, need help setting up vxlans, Please guide me ,
Hi, Am also facing the issue with Cisco 9606R and Hirschmann MTS series. Cisco 9606R is stacked and connecting 2 interfaces of 25Gig slot with 10Gig SFPs towards Hirschmann MTS AggSw1 and AggSw2 Both Hirschmann AggSw1 and AggSw2 is further connecting...
Hi,I am trying to invoke the recommended password recovery procedure for a Cisco Nexus N6K-C6001-64P v01 network switch using Putty and/ or TeraTerm VT terminal emulators?? I'm using a standard UK QWERTY keyboard but the recommended keyboard sequence...
Hi everyone,I have this network diagram here and I can't figure out why when I connect the link between C101 and C109 I have lots of packet loss and issues on VL60.Every port that connects the switches has every vlan (1,10,20,30,40,60,70,80,90,100,20...
Hi, I have new stack and after 2 days these warning starts appears. 21474834552022-Oct-24 15:49:23Warning%STCK SYSL-W-UNITTRP: UNIT ID 2,Trap:%Box-W-I2C-FAILURE-READ: I2C failed to read information from device at address 0x2E on bus 0 offset 0x28, co...
