We have about 18 Polycom HDX units throughout our system, and every time we connect them in a call, they receive and send content in the video window. This obviously results in unreadable content and frustrated users. We have reached out to Cisco,...
Forum Posts
Hi! We have a number of large lecture halls setup with a SX80, presentertrack and speakertrack. The way we have been switching between the presenter and speakertrack camera is through a physical toggle switch. The toggle switch is connected to a Cres...
Resolved! CUCM license for third party equipment
Hi! I want to connect a CUCM V11.5 to Polycom equipment, I do not what kind of license use in order to have video conference and communication between equipments, is it possible to de CUCM look it as third party? Thanks in advanced, Best Regard...
After upgrading a working CUCM registered Room 70 Single from CE 9.2.1 to 9.5.2 it appears from logs the camera is still stuck at firmware 9.2.1 Screen shows “No Camera Connected” So far I have upgraded about 7 Room 55s to CE 9.5.2 and haven’t ha...
I have 4 Tandberg MXP 1000, Software ver F6.0 NTSC, one with F6.1 NTSC. These are in a detention center environment and are set to auto answer. I have purchased a new Telepresence DX80, software ver ce 9.1.4 5f64050 2017-08-25. I have got...
Hi everybody, I have a Room Kit Plus P60 with 2 P60 cameras. 1st camera is working well but 2nd camera is not. I connect 2nd camera to codec by 15m HDMI cable. I converted from PC to camera on Web Administrator. So it still has problem. I dont unders...
Hi Guys pls find attachment 's Inside jabber works fineso far , CUCM to EXP-C has tls connection = status = Activethe MRA zone is active between EXP-C and EXP-E , status = Green the outside jabber user has the below nslookup: > set type=srv> _collab...
We have a small deployment of Cisco RoomKits with Touch 10s running the latest CE 9.5.x code and our management has complained that every time they press the call icon it automatically takes them to recents instead of the directory. I havnt found any...
Resolved! CMS and CUCM v9.x to 11.x
Hello, I have a CUCM 9.5 and I am still on contract, so I can upgrade to v11.5, my question is all the licences I have, will get lost? I have UWL Standard Then, I want to add a Cisco Meeting Server, is it possible to make multiperson video calls wi...
Hello All, I have the following server in my installation: 1- CUCM for call control 2- TMS server 2- Two CMS 3- 20 endpoints (MX 300 series). The Trunk and Conference Bridge are configured in CUCM to the Both CMS. I have tested the both confe...
Resolved! CSM and CUCM v9.x to 11.x
Hello, I have a CUCM 9.5 and I am still on contract, so I can upgrade to v11.5, my question is all the licences I have, will get lost? I have UWL Standard Then, I want to add a CSM server, is it possible to make multiperson video calls with UWL Sta...
Hi all I am currently trying to deploy CMS (2.2.10) with user sync from ADLDS From what i read online, LDS is just another LDAP server, which i think should be supported on CMS. The problem is that LDS is using secure connection (636 - SSL), i ca...
Resolved! Localization of TP10 in-room controls
Hi, I am using the in-room control and macro editors to add a button to switch languages to the TP10. The Call, Share, Messages buttons all switch languages correctly, but other custom buttons do not, they stay in English. Is it possible to code this...
When I create a new contact, set up the protocol (ex.Protocol:Auto), when I want to edit the contact,I changed the protocol: Auto→H.323 and save, the protocol changed from Auto to H.323. But I changed H.323 back to Auto,Protocol can't change it back...
Hi,We have a TMS platform and some cisco endponits. We have got some new Yealink endponits VC800, but we don't know how to make VC800 get phonebook from Cisco TMS. Is there any documents or API for third party endpoints about how can third party endp...
