Good Morning All! We are currently experiencing an issue with neighboring our VCS expressways. All of our neighbor zones show "Active" with dial rules configured and all required ports have been opened on the firewall between our Controls and Ex...
Good Morning All! We are currently experiencing an issue with neighboring our VCS expressways. All of our neighbor zones show "Active" with dial rules configured and all required ports have been opened on the firewall between our Controls and Ex...
Looking for clarification on whether OneTable is available for the CTS3x00 endpoints. The TelePresence Server data sheet indicates that is only available on the T3.http://www.cisco.com/en/US/prod/collateral/ps7060/ps11305/ps11317/ps11339/data_sheet_c...
Are there any document that describe the communication between TMS and CUCM / CTS.Or maybe someone know which protocols that are used? //Robert
Does anyone know how to disable the Cisco tones on call start and end on the CTS systems. I have looked everywhere in CUCM and do not see any type of setting for it as well as performed the cursory searches via the web. When I am testing I get so tir...
Hallo all,i have VCS infrastructure with VCSc, MCU, TMS and about 30 Cisco E20 phones. Phonebook is integrated with Microsoft AD. I see contacts in the phonebook in TMS, connection to the AD is fine, E20 configured fine(i think:)). But, the E20 phone...
Hi all,I'm facing a problem with MPS 200 that need your help. In particular, I created new conference, but when adding participant, the message "MediaC. 0 FAILURE" is appear on LCD and the FAIL alarm blinks continuosly. As a result, conference isn't ...
I know that you can reset the "admin" account passwords from root, by running tsh, but can you change the 'root' password from within the 'admin' tsh?
Hi,We have a CTS 500-32 with touch which is running on 1.8.1 and registered to the CUCM 8.6.2a. While we connect calls the calls get connected and are unsecure. The other CTS endpoints we have cert installed on the IP phones and Codec. The calls get ...
Hi All, We have a VCS Control and VCS Expressway and endpoints. VCS control and endpoints are in the same subnet. We have recently purchased a dedicated internet link for video traffic alone. I have configured the policy based routing in the LAN so t...
Dear ALLI have a Problem with a TMS Provisioning Directory which are synchronized with the AD Directory.if I start manually to synchronize, than is working fine.I see in the Info that will be the next start 4:00am but this does not synchronized wit...
Hello, What do you think about using a neighbor zone on VCS for MCU in SIP against classic registration. It's the only way i found to palliate SiP generic préfix registration leack.Tank youRegardsSent from Cisco Technical Support iPad App
Hi All,Using the cisco router (2900 series) as an SIP to E&M gateway. On one side we have a SIP device and on the other side of the gateway we have an E&M device.When the E&M device terminates a call the gateway should issue a SIP BYE message to the ...
hi,when i connect analog line direct to analog phone the voice volume is fine but when i connect to 2911 router (fxo port) the volume is low. i have cucmbe8.6 as call agent and 2911 as voice gateway.. following is the config for voice portsvoice-port...
what is the frame rate when I using the PiP as presentation output if I have presenation codec
Hi,After a long search, I don't find information on the process of update release key for the endpoints in the TMS.In TMS, some endpoints don't have license key for the update although they are under maintenance while others pick them up correctly....
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-23-2025 07:20 PM | ||
05-19-2025 05:53 AM | ||
05-18-2025 06:22 PM | ||
05-02-2025 12:56 AM | ||
04-15-2025 12:31 AM |
User | Count |
---|---|
1 | |
1 | |
1 |