I am having a weird issue with the COBRAS Import Hot Mode. We are utilizing a Server 2008 R2 instance as an Application server to run all the Cisco Unity Tools. We are running Unity Connection 9.1(2) SR1 on both servers and all servers are in the s...
Is it best practice to "shut" unused voice-ports on a VG when MGCP is involved and there is no config on the port in CUCM?If yes, why?
Previously I had a discussion here for a 911 Configuration that worked out perfectly. However, the main office, I always thought for 911 was working correctly. Now, I’m not so sure as this configuration was implemented before I came along. Currently,...
Hello everyoneI have CUCM and CCX 11.6 .i have set Maximum Call Duration timer to 30 minutes so my agents get disconnected in 30 minutes. but when they push Hold button the timer resets and they can talk for another 30 minutes . they don't even need ...
I know I can configure intercom on an 8800 series phone to "whisper" to the call recipient and in order to have a two way conversation, the recipient will need to press a button on their phone to allow the two way conversation. Is it possible to prog...
Hi, We have a location using CUCM and integrated with the InformaCast paging application. The paging system is currently setup to use MAC address based zone, we would like to change the zone type to IP address based but can't find any documentation ...
Is there a supported SFTP server for saving reports? We can get this working using http://www.freesshd.com/ but its not the most up-to-date & doesn't look like its maintained. Preferably we'd like to use FileZilla Server or CoreFTP, we have tried the...
Is there a way to deploy SMS & MMS to Jabber Clients, and IP Phones? Is there Text Capable DID numbers delivered by the service provider? Most of my users will not use Jabber, because they tell me that its totally useless to them, because there is ...
If we have two active SIP trunk configured and we decided to add that in Route group/Route list, if one of the ISP link is down in one router(sip) how does CUCM make decision on routing the call to second Router- Although SIP trunk is up from CUCM to...
The cucm version is 9.1.2. I need to install a cop file for Cisco Telepresence 1300-65 model. Post installation I need to restart the TFTP services . It's running on Publisher and one dedicated TFTP Server(Primary Type). Is there an order do I need t...
Are any of the Cisco ACs compatible with multiple CUCM clusters? We have CUCM 8.6 and 10.5. Is there any AC that can happily take takes for both? CheersRich
Hello Cisco Community, I have a CUCM Cluster (one Sub & one Pub) connected to a Siemens PBX via a VG.The CUCM Dial Plan is 5XXX and the PBX is at 2xxx.I set everything in my CUCM I can now make calls from and to it within my local site Samething with...
I currently have CUCM version 9.1.2.13900-10, CUC version 9.1.2.13900-621, CER version 9.0.2.10000-1, and CUP/IM&P version 9.1.1.61900-7 running on UCSC-C220-M3S hardware. My understanding is I can upgrade any one of these apps to version 11.5, and ...
HiI'm planning to migrate cucm & UC version 9.1. It's currently running on MCS server. We need to migrate to UCS then planning for upgrade the version to 11.0. There are two cluster in the environment. One has 5 nodes other has 10 nodes. Planning to...
We are using VG310 gateways for analog Fax, Credit Card, Fire Alarm usage and found that the company that monitors the Fire Alarm lines have installed a SIP 204 Gateway in front of their monitoring system. Once they did this it has caused our Fire A...
| User | Count |
|---|---|
| 9 | |
| 3 | |
| 2 | |
| 1 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
