Hi,we have a C220-M4L with 4 HDD disks configured as Raid 10 with two partitions.Now I want to move to a Raid 1 with 2 SSD instead, the remaining 2 HDDs would be removed. Is that possible without rebuilind the server, in particular re-installing the ...
Forum Posts
1. I would like to know when the link grouping preference in ucs global policy should be set to None. Or what's good?2. I also want to know the advantages and disadvantages of Port Channel in the classis fex discovery policy.
Resolved! [FSM:FAILED]: user configuration
Hello, I got below alert after upgrade the UCS manager from 4.0. 1d to 4.0.4d. Could you please let me know how to resolve this issue. This is critical alert and what is impact of this alert. Affected object : sys/user-extDescrip...
Hello,I am doing some tests (in the laboratory) to analyze the possibility of creating the monitoring of a Cisco UCS, below it follows the tools that I am using for this laboratory;Cisco UCS Platform Emulator (versions 3.1.2e and 2.5.2a)Cygwin Termin...
Resolved! UCS Diagnostic ISO
I'm trying to test the RAM in one of our blades using the Diag ISO https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/ucs_diagnostics/b_UCS_Blade_Server_Diagnostics_User_Guide-2-0/b_UCS_Blade_Server_Diagnostics_User_Guide-2-0_chapter_01.h...
I'm trying to connect the US FIs to direct attached storage, and when I go into the FIs to configure the fc ports, it's requiring that the storage ports start on the left and go to the right, with the ethernet ports on the right side. I've set up th...
Hello, I have an issue with a UCS C220 M3 in that it is in a continual boot loop and can't even get to the boot selection menu. This occurred while I was using the HUU to upgrade the CIMC and BIOS. After the reboot it has been in this state. After a ...
First time working on a UCS server. I have a new C2205 M5 that I'm setting up. Two drives are installed, and are present under physical drive info in CIMC & SCU. But, neither drive is listed as an available physical drive to configure for RAID. In C...
HiThe NPIV/NPV in UCS blade is not properly configured, the UCS blades are B200 M5 seriesThe SAN storage is provided through MDS9706 fabric and the NPIV protocol is able on MDS fabrics and working for Oracle virtual machine and AIX/vios environmentsT...
Hi Can anybody please advise on the below, I am recieving this error, however the cluster itself is healthy KERN-2-SYSTEM_MSG: [112916207.001611] mts_do_msg_input() failing since no space available in 2288 (src_sap = 2288, opc = 7679) - kernelsvc_sam...
HiWe have have an updating server profile template applied to five blades to configure for booting from a SAN via iSCSIFirst time we have set this up so the learning curve has been steep and we discovered that each server needs a separate target init...
Resolved! Disable memory dimms on C240
Hello, I am looking for a way to disable some memory modules in a C240 M5 server.Is there a "software" way (e.g. via certain policies) besides physical removing them? The server is managed via UCS Manager. Regards Martin
Hi All,I have an alert for the CMOS battery on the system board of a blade server in a Cisco UCS B440 M2.- CIMC | Voltage P3V_BAT_SCALED #0x00 | Lower Non-critical - going low | Asserted | Reading 2.42 <= Threshold 2.42 Volts I reviewed the sensors a...
Hello all,I have a fully populated 5108 chassis with 8 x B200 M5 servers.The chassis has 4 power supplies which are configured in a grid mode.Power supply 1+2 are connected to the same PDU and power supply 3+4are connected to a different PDU.What wil...
hai, i have CIMC eror, "Reboot and select proper boot device or insert boot media in selected boot device and press a key." before is normal, but after i reboot, the problem is come. please help me thanksRT
