Hello, I'm trying to use the following UCS power tool command to create a hardware profile to load into Cisco's online HCL tool here: https://ucshcltool.cloudapps.cisco.com/public/#uploadedprofilesUnfortunately all I've found is the syntax here: Ci...
Forum Posts
Is this correct? That, should one or two drives fail in a stretched cluster environment, the cluster fails over to the remote site? I don't think it is but either way the documentation should read more clearly.
Resolved! UCS C220 / C240 M5 acceptance tests
Dears I am preparing hardware acceptance document for the UCS C220 / C240 servers which will run as standalone solution I have prepared the steps needed to check the hardware components GUI and CLI but I have read about Cisco UCS-SDU utility which ca...
HiÍ nerd tiverdes my ucs , Wing haver 2 Fiber interconnect . When I finishbreset using reset configurations, it goes directly to options where said detected peer fiber will b add to the cluster.. I need to reset and start from scratch, See the att...
I got into a new environment and saw UCS is using nimble storage with ISCSI. but they are using 1500MTU as opposed to 9000. IS is not best practice? how do I check for any dropped iscsi frames?
I got VMs on the same vlan as the pxe/tftp serer but they are not pxe booting. I have the vlans right. how do I do a packet trace from the vm to the pxe server via the FI?
When will Cisco have a Server system, Cisco UCS, as follows: Dual LGA 3647 4.5 GHz processors with 8 PCIe Generation 4.0 x16 slots? Thank you.
Resolved! CIMC Missing or does not exist
I have a UCS C220 M3SBE server and cannot get CIMC to work on it. When booting I can hit F8 and it will say its loading CIMC config utility but it never boots into it it just boots to the OS. I have tried multiple times. Is there a part CIMC needs po...
Resolved! C-Series CIMC Firmware Upgrade
I have a couple of C240 M4's at remote offices and need to udpate firmware on them. I'd like to update CIMC first, then boot the HUU iso and update the rest of the firmware. However, I can only find the HUU download, there doesn't appear to be a wa...
Hey All, I just need to confirm that the Cisco C220 M5SX blades have embedded LSI controller, which hypervisor hides the drives from the ESXi installer? ESXi 5.5.0 (yes i know, environment limited) I have configured the drives in RAID 1, as a bootabl...
My question is specifically around how to tell if a call home xml alert is cleared or not. I have noticed that in an alert, there are several values which point to alert severity. 1. in the envelop body: <soap-env:Body> <aml-block:Severity>5</aml-blo...
Hello team! How are you? I have to configure a server c240-M5 with SMB services as storage to a few server blades in a mini UCS chassis.How would be the procedure/configuration in the ucs to commit this? I attached a topology.Thanks in advance, i was...
I am looking for a list of steps to replace a failed 6248 FI in a 3.1.3a UCSM environment. Got a new 6248 in an RMA from TAC but want to make sure we replace the failed FI with the right steps. Thanks for any guidance.
I need to get all serial number off the Cisco UCS environment (Chassis/blades/stand-alones) so I connected to the UCS Manager using my domain credentials and putty. I am using the command:show chassis inventory expand > FullInventory_2019-05-29 Only ...
We need to connect a UCS C220 server in a FI and reach a network. c220 servers 40gb slot are connected to 6332-16up 40 gb port. If I set the port to network uplink. my vms on other servers got lost connection. maybe because if Netwprk uplink configur...
