Hi,we need to chage the IP of UCS Central due to some conflict, but the UCS Manager is regsiterd in UCS Central using IP, how can we register with UCS Central FQDN without unregistering it?
Forum Posts
Hello,We have a number of Cisco UCS M4s which we no longer have hardware support for, however there are some legacy applciations running on them, so we need to keep them running for the foreseeable future. We are currently running 3.2(3c) on the Infr...
Hi, all. Installed Server 2022 on one of my C240 M5s and it's missing a PCI Device driver. I downloaded Cisco's most recent Drivers ISO for Windows, but it doesn't seem to have it. Any thoughts on how to identify what's missing?Thank you.
VMware 7 running on UCS-E180D M3 , cannot get the internal nics online, they are Broadcom Corporation NetXtreme BCM5719 Gigabit Ethernet running the latest vmware U3 NTG3 driver , belowntg3 version 4.1.9.0-4vmwThe crazy thing is that the information ...
Hi Everyone,I would like to know if the UCS C220 M5 server supports Intel Optane DC Persistent 128GB PC4-2666V DDR4 ECC Server RAM NMA1XXD128GPS memory module.I'm about to buy 2 modules but I'm newbie and this server is my homelab. best regards,Dougl...
Hello guys,I'm trying to configure UCS-C240-M7 server in Cisco ccw. I'm getting the following error after configuring, Please note that this product may not be purchased outside of the approved bundles. Please use MLB: UCS-M7-MLB. (CE202322)When I lo...
Hi Everyone,my server is a UCS C220 M5L has LFF4-drives, however, when opening and checking the MegaRAID card I saw that it indicates 8i but have 2 cables with only 2 conectors each one are connected the 4 x 3.5" HDDs.Could I replace these cables wit...
I'd be curious to hear candid thoughts, advice, opinions about migrations from HyperFlex to Nutanix based on personal experience.(Four years and 10 months to go, according to the official roadmap announced to the media.)
Hellow everyone, I have a 3-node lab environment set up and installed with ESXI 7.0.3 and a vCenter VM nested inside the first node. There was a power shutdown, so i shutdown all the VMs and then shutdown the vCenter VM last. After the power mainte...
Resolved! Redhat 8.4 on UCS C220 M5 Rack Server
Hello,I can't update my Redhat 8.1 to 8.4 because the megasr module is not available for Redhat 8.4 !https://software.cisco.com/download/home/286318809/type/283853158/release/4.2(1c)Last month update gives only drivers for Redhat 8.2, is it a joke?An...
Resolved! UCS FI 6332 Unable to login.
Hello Community!I have a cluster of FI 6332 System version: 4.0(4n): A: UP, SUBORDINATEB: UP, PRIMARY And I have an error trying to ssh primary B or vip ip: Unable to login. You have reached the maximum allowed number of concurrent sessions. Please ...
Hi!I need to clear the cached SSH keys in my UCS enviroment. I have tried SSH to the Fabric Interconnect and connect to local-mgmt and thereafter issued the command "clear sshkey x.x.x.x". This yields an error message of "Permission denied" to the fi...
Hello. I have two retired UCS C3160 servers, each with a single M3 server node. I'd like to try upgrading one of the servers to a C3260 by moving parts from one C3160 to the other.That said, would it be possible for someone from Cisco to please answe...
Hi all,I have Fabric Interconnect 6120 firmware 1.4(1m), suddenly my UCS manager problem error is "Software Error: Exception during execution: [Error: Timed out communicating with DME]" and my console ucs manager via GUI error is aplication to time ...
I am attempting to connect a UCS C220M5 node with SFP-10G-T-X in the SFP ports and Cat6a to a 10G RJ-45 port on a Catalyst 9300 stack. No link is being established. Are there specific commands to enable that SFP in the UCS node?NIC: UCSC-PCIE-C25Q-04...
