Unified Computing System Discussions

Hi, I'm about to add a second power supply to each of my USC C220 M4 servers. Since it's a production server, I just want to make sure, it's hot swappable and it's not require the servers to reboot. The PW PID VID = UCSC-PSU1-770W V01 Cisco PN = 341-...

Hello: We have Cisco UCS v 2.2(6e) with VMware vSphere 5.5U2 on top. We plan to use pVLAN (Isolated) in UCS in conjunction with Distributed (not standard) vSwitch in vSphere. Is it fully supported?  Because in prevous versions of UCS it wasn't Tha...

Hi Guys, When I try to launch KVM console from UCS manager, it asks for username, password and IP address. I have seen an environment where this prompt does not come up, it just goes straight and launches the KVM. Also I am not sure what credentials...

Greetings from the Big Data world!I am installing SUSE linux version 11sp3 (for SAP applications) on a B series blade. We are booting from a LUN on our SAN storage device (PURE). After successfully installing SUSE linux on our LUN, when the blade reb...

I post this to warn you of a nasty bug, which I didn't know and which seems to be well known (> 100 TAC cases) One of my customer wanted to firmware upgrade from 2.2.3 to 2.2.6e and brought down his whole environment (Super Gau) All the B200 M4 blad...

We are going to migrate from a direct attached storage to connecting to our Brocade Fabric switches.  I understand that this is disruptive and both Fabrics will go down at the same time when switched to End-Host Mode. This was discussed in the follow...

Good morning, I have an alarm on UCS server, please if anyone has any idea what may be the origin of this fault has not reoccurred just appeared and has remained alarmed. Cisco attached capture CIMC. I hope your comments., Thanks and regards, Cam...

I know how to rename the hostname on CIMC gui. I just don't know if there will be impact when changing it. Do I also need to reboot for the changes to take effect? Are there other things do i need to do/check before and after renaming?

I need to configure NLB on N5K.as per cisco doc i am doing below configuration:interface Vlan10  no shutdown  ip address 10.1.2.1/24  ip arp 10.1.2.200 03bf.0000.1111mac address-table multicast 03bf.0000.1111 vlan 10 interface po 11 i am not able to ...

Hi, Could someone advise on whether there is a possible typo on the matrix for C220M4 and VMware 6.0 and LOM adapter driver version I have installed VMware ESXi 6.0 U2 Cisco version on a C220M4 - when I check what LOM driver comes with this it is ig...

i injected the 2012 r2 lom and storage drivers into windows 2012 r2 cd and installed 2012r2 fine but under device manager, i am sill seeing a bunch of devices without drivers. any idea what drivers im missing?

Hi Guys , hope you are all fine . I'm getting some error when trying to login to UCS Manager [see screenshot below] I'm familiar with this error when the primary FI is down , but here , both FIs are up [pingable] . Can someone please assist ? we ca...

Hi Guys , We got 5 new B200-M4 blades [see the screenshot attached , it got SSD HDD] and everytime i'm trying to ,mount CD/DVD , it said "the selected device could not be mapped" I tried all the available options in the Boot Order Policy for CD/DVD ...

We have 3 UCS C210 M2 running ESXi 5.5, how does Cisco handle the updating of the hosts to the latest version if the hardware is on the VMware HCL? These are running our Cisco CM and Unity 9.1 VM's.