Unified Computing System Discussions

Resolved! windows server 2012 on 2.0 (3c)

I see in the interoperability matrix for 2.0 (3c) fi fw that windows server 2012 is not a supported operating system. Will it still work with a certain driver package?Is there a minimum version of FI firmware in order to run windows server 2012 on B2...

KVM IP vs CIMC IP Address

1) The IP assigned to the CIMC chip the one that the remote KVM uses correct?2) The IPMI IP address is assigned to what part of a B-series blade?Thanks

UCS Platform Emulator Downloads (latest: UCSPE 2.2(1bPE1))

The following Cisco UCS Platform Emulators are available for download from Cisco UCS Communities:Latest Cisco UCS Platform EmulatorCisco UCS Platform Emulator version 2.2(1bPE1):Details on this ReleaseDownloads:Download UCSPE 2.2(1bPE1) OVA or ZIP (R...

Cisco UCS Blades equipped with a Fusion IO card

Has anyone done Cisco UCS Blades equipped with a Fusion IO card, in a ESXi VDI environment ? e.g. can one just install the proper driver for ESXi, and then access Fusion IO card as a disk ?Is it correct, that this doesn't require a Raid controller...

UCSM upgrade required to support Ivy Bridge processor?

Using UCSM 2.1(1f). Purchased three B200 M3 blades with Ivy Bridge CPU not supported until UCSM 2.1(3a). We're told we cannot upgrade the firmware for those blades only and the Compatibility Catalog, but must do a complete UCS upgrade to 2.1(3a). ...

FlexFlash Mirror with firmware 2.2 Can I mirror SD card 1 to SD Card 2 nondestructively?

I have B200 M3 series Blades with ESXI 5.1 loaded on UCS-SD-16G 16GB SD Card module, I have since upgraded chassis and blade firmware to latest version 2.2 and installed a second UCS-SD-16G 16GB SD Card module in each bladeMy question is Can I mirror...

Error while configuring CIMC network using Standalone C-Series CIMC XML API

Hi,I'm trying to use the C-series xml api to retrieve and configure Cisco CIMC. I'm following this document : https://communities.cisco.com/docs/DOC-36278?expandComment=trueI've got authenticaiton and retrieval working but configuring using the confi...

Named policy unresolved (again)

I would like to find an explanation of this error messageCan't find it in http://www.cisco.com/en/US/docs/unified_computing/ucs/ts/faults/reference/2.0/UCSFaultsErrorsRef.pdfCisco UCS Faults and Error Messages Reference August 2012

Ask the Expert: Cisco Unified Computing System Director

With Andrew Nam Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco Unified Computing System (UCS) Director with Cisco expert Andrew Nam. Cisco UCS Director was...

Unable To See Global Pools/Vlans

Hello, im working on a test deployment of UCS Central. We have a Spare pair of UCS 6120 FI's with a Chassis and blades for the test.We have built out the UCS central server, and registered the pod with UCSC. I have Set all settings to global, and...

Resolved! Firmware upgrade from 2.1(3a) to 2.1(3b).

I don't find any documentation on the web for firmware upgrade from 2.1(3a) to 2.1(3b)..is it wise to follow this link http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/upgrading/from1.4/to2.1/b_UpgradingCiscoUCSFrom1.4To2.1.html ?Any best pra...

Resolved! Upgrading UCS1.4l to 2.1(1a) cannot transfer the primary role

Upgrading to 2.1(1a), got everything upgraded to the point of the fabric interconnects.. Upgraded the subordinate, its online, ready, happy.. What I can’t seem to do is failover the primary ( version 1.43l) to the secondary so I can then upgrade the ...

Zoning, direct attached Netapp

UCS V2.2.1b, FC switch mode, Netapp filer direct attached with FC.SP with 2 vhba, one mapped to fabric A resp.B., 2 FC target end point, one in fabric A, resp. B.If I check the zoning done by UCS, I actually see 4 zones (SIST) ? why ? I would only ex...

second-level boot devices

Can someone please explain, what second-level boot devices are used for ?In the documentation it says: For Cisco UCS M3 blade and rack servers in UEFI boot mode, you can select both top-level andsecond-level boot devices. For all servers in legacy ...

Resolved! A lot of UCS F0502 and F0801 error need to been resolve

Hi expers,Recently we purchasing a lot of B200 M3. After we boot up server. UCSM show all the CPU and Memory error "F0502" as image in the below. Have any one also encounter same issue? And how to fix it?Best regards,Meng-Yuan Hsieh (Nick)

Unified Computing System Discussions

Forum Posts

Resolved! windows server 2012 on 2.0 (3c)

KVM IP vs CIMC IP Address

UCS Platform Emulator Downloads (latest: UCSPE 2.2(1bPE1))

Cisco UCS Blades equipped with a Fusion IO card

UCSM upgrade required to support Ivy Bridge processor?

FlexFlash Mirror with firmware 2.2 Can I mirror SD card 1 to SD Card 2 nondestructively?

Error while configuring CIMC network using Standalone C-Series CIMC XML API

Named policy unresolved (again)

Ask the Expert: Cisco Unified Computing System Director

Unable To See Global Pools/Vlans

Resolved! Firmware upgrade from 2.1(3a) to 2.1(3b).

Resolved! Upgrading UCS1.4l to 2.1(1a) cannot transfer the primary role

Zoning, direct attached Netapp

second-level boot devices

Resolved! A lot of UCS F0502 and F0801 error need to been resolve

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

Unable to use an M2 SSD with a PCI adapter on Cisco C220 M4

UCS blade chassis network error

Export from 6248 Fabric Interconnects and import to 6454 FIs

Help, i have a question about Vlans overlapping different vlan groups

B200 M5 Stopped During Boot.

Unable to upload SSL

UCS - B200 M3/M4 - Local Disk Configuration

Managing vNICs and vHBA's

Compatibility query

UCS Port Channel LACP policy