Dear Team,On the Fabric Interconnect see Switching modes,,will you be able to tell me the scenario when each mode will be used on real environment?RegardsJose
Hi,as I read in the ordering Guidehttp://www.cisco.com/en/US/prod/collateral/ps10265/ps10493/spec_sheet_c17-644230.pdf the C210 has to be ordered with a SAS-Expander to use more than 8 Disks with LSI MegaRAID SAS 9261-8i according to the Orderin...
Hello,I'm trying to monitor my UCS C260 using SNMP traps sent to HP SIM. In order do import the Cisco MIBs into SIM, you compile a .cfg file. One of the MIBs, CISCO-UNIFIED-COMPUTING-TC-MIB, will not compile. When running the mcompile command, I get ...
Hi,I have two C210 M2 Server with LSI 6G MegaRAID 9261-8i Card with 10 hard drives of each 135GB. When I tried the automatic selection for the RAID configuration, the system has created one virtual drive with RAID 6. My concern is what the best pract...
I am in the middle of deploying serveral UCS chassis and servers that will run ESX 5.1. Our McData (brocade) switches are no longer supported by cisco and subsequently will not work with ESX 5.0 or higher. ESX 4.1 does work though. Has anyone had any...
Hi team ,We are getting error on PSU for Cisco UCS chassis. Its showing NA under performance & voltage tab.We tried resetating PSU as well as removing power cable & connecting it back.PSU is power-on & operational.Can anyone suggest why this issue is...
I am trying to build a service profile for vmfex but I keep getting a config errorI only have 2 vnics assigned to this blade and I have a dynamic vnic connection policy applied. how many dynamic vnics should i be using? does this depened on how many ...
Hello,I am using UCS Central 1.1.1a and have spun up couple of UCS Emulators to see how the UCS central works. I was able to register the UCS central on 2 UCS Manager domains. But these UCSM are not being displayed on the UCS Central GUI. Do I have t...
Hi guys,Just wondering if anyone could help with an odd issue we seem to have come across with our UCS manager. We have set it up to use LDAP authentication for log on which is working fine for four of our five team members however we have one user ...
Hello, I finding a old fault, which has been cleared of the faults view. I don't see it in Events view. How finding a old fault ?Thank for your help.Stéphane
Hi Team ,We rebooted Fabric interconnect yesterday & found below errors on FI console.Pls suggest what is cause of it & how it can be rectified.syslog[5182]: ERROR, mts_send failed, ERROR = -1, ERRNO = 22 syslog[5182]: ERROR, mts_send failed, ERROR ...
Hi, I would like to know whether the F2e Line cards can do Layer 3 OR do they rely on M1 cards for it? Like the F1 cards, did not do any L3 stuff and internally routed from the fabric backplace to the M1s for all L3 functionality. thnx
not sure what happened but when i rebooted my esxi 5.1 host i am getting a no compatible network adapters found esxi 5.1 message and there is not nic adapters.in the sevice profile , nothing has changed. just 2 vnics, vnic0,vnic1any ideas?
Hey all,I have a Cisco C240 M3S that I will be utilizing as an MS Exchange Server with MS Server 2012 Std Edition. I am performing stress testing currently on the server and constantly receiving the following error: "Controller ID: 0 Controller ...
Hi Team ,Yesterday we performed Blades & chassis shutdown due to some maintenance activity in Data center.We removed power cables from UCS chassis.After maintenence activity , we connected all power cables back to UCS chassis. After sometime all bla...
