We need suggestion . Can we install Finisar 10G-850nm VCSEL SFP.P/N-FTLX8574D3BCL in UCS 6248 FI switch to connect UCS Chassis 5108. Any draw back
Forum Posts
We have a scenario of Two FI 6332 to connect uplink as "Single Uplinks to Single Switch"...No VPC/VSS...We have Single 6509 with Single 10Gbps card; and no choice to use it. My Eth1/1 port on both FIs is configured as Uplink Port (as Trunk). Fabric I...
Resolved! HyperFlex vmware vcenter doubt
Hi,Checking BoM I saw that hx nodes Will come with esxi 6.7 pre-installed and with license.But i dont see nothing Talking about vcenter. Do we need to buy vcenter Separarly to vmware or license its included with Hx nodes?
Hi,I am getting below error while installing hyperflex via Intersight. Installation is failing at 66%.Failed in Task: Copying Preliminary Software Packages Checksum File to Storage Controller VM(outbound) with error: 'Failed to connect to svc.ucs-con...
Hi, We have a Cisco UCS 5108 with two Cisco UCS 6324 Fabric Interconnects. We want to connect the FI's to 2 upstreams SAN switches. In order to accomplish this, we need the change the FC mode to End-host mode.The physical FC ports are now configured...
Hi,I have UCS C220 M3 server, in our lab environment, the server is giving out extreme loud fan noise, I believe this is caused due to couple of fans showing not running in the CIMC. I can see the fans are running fine, and I tried swapping them with...
Resolved! SSD and HDD on same RAID controller
I am planning to create two virtual disks connected to the same 12g RAID controller on a UCS C220 M5 server.1st Virtual Disk will have three SSDs (RAID 1 with dedicated hot spare) 2nd Virtual Disk will have 7 SAS HDDs (RAID 10 with dedicated hot spar...
Hi, how to make this with power tool? As I know its possible to assign vNIC template when adding new interface, but how to modify existing ? Get-UcsServiceProfile -Filter 'Name -ilike XXX*' | Add-UcsVnic -NwTemplName 'NewTemplate' -Name 'eth1'
Hi,Can someone please suggest me on good monitoring tool for Cisco Hyperflex solution ? We have Vrealize operations Manager what we use to monitor our Cisco UCS environment, so can we use same for Hyperflex also ? Do we have some better tool availabl...
As a Cisco partner looking at all the Intel supply chain issues , is Cisco considering using AMD more widely in it's UCS server product line ?
Resolved! Removing domain from UCS Central
I have a 6248 domain I would like to remove from UCS Central, and have a couple of questions. We're running Central version 2.0.1i and firmware version 4.04b. This domain I would like to remove does not have any chassis or rackmounts connected, and...
Hi I'm trying to connect to ucscentral in my powershell profile that works fine. But when profile script ends the connection is not saved in the $global:DefaultUCSCentral variable, thus making it impossible for me to reuse the connection. How can th...
Resolved! IOM upgrade during outage?
Hello! I have two chassis, one with 2204XP IOMs and one with 2208XP IOMs, and I would like to upgrade them to 2304XP IOMs (we have 6332-16UP FIs and already have one chassis with 2304XP IOMs on the domain). Soon we will be moving this domain to a n...
Hello, We would like to connect a tape drive directly to a vNic 1227 (C240 M4). The negociation from the tape drive was configured as "loop" for direct attachment. The device is still not discovered by our Windows Server 2012 R2. Is there a configu...
