Good afternoon.Added to my provision Dial Plan P Timer, but it does not work.I pick up after 5 seconds is presented a message about an invalid number.Tried to do as stated herehttps://supportforums.cisco.com/docs/DOC-18128but it still does not work, ...
Hi Guys,This seems faily abnormal, Recently got some WBPN's (Replacement of WBP54G). for 2 x SPA phones. The phones register and work fine via ethernet. However, when I plug in the WBPN to the phone, it won't register. It looks as if it's giving "Rea...
I'm having a hard time changing the UC560 Data VLAN IP from192.168.1.60 to 192.168.0.60.In CCA, when I change the IP and submit, CCA gives me a "Java Null Pointer Exception" and freezes at "Configuring DCHP Pools and Exclusions".Has anyone seen this ...
I have a UC320 and the coverage is not adequate to allow my wifi phones to connect. I then purchased an AP541N access point, and would like the distant wifi phones to connect to the AP541N and register that way. The phones don't seem to want to c...
I have a UC520 with a lots of 7975 and 7970 running. I am able to create conference,but when I want the see the conference List pressing the button I don´t get any result.Does anyone can tell me how to look on this or make any traces?Best RegardsKlau...
I like that CUPM can do Day 1 Setup, ie Dial Plan Creation, CSS, Partitions, Device Pools, etc.However, as you know there are 50 ways to setup CUCM and everyone does things a little different. I want to see CUPM configurable so that we can setup wha...
Hey Guys,I was wondering, and I need to know for my business, is there any way at all for me to make my Cisco SPA 303 VOIP Phone to ring by sending a packet through my local network?I would like to just be able to click a button or send a command thr...
HiI have problems get the SPA 504G working with the newly delivered UC320W.UC320wsoftware newest version 2.3.2(6)SPA firmware 7.4.7 v32one of uc320w lan port is connected to sge 2010p via trunk link with vlan 1 and vlan 100 tagged allowed.spa 504 g ...
Hi everybody. I have installed an UC 320 to a client. There is a small issue with the disconnect tone. We have 3 FXO lines connected with 2 different telco. FXO2 and 3 correctly detect the disconnect tone from one telco, but the FXO1 that is connecte...
Hello,I have been able to record and play back ringtones on my 7945 and softphones, but the playback sounds awful.I have used the .raw file format.I have used the 8 bit signaling.I recorded the sound file using a Logitech headset (not the most expens...
Team,I have a customer with a UC 560 at the HQ site and 7 fxo lines. They also have a remote site with a 2800 ISR router termination the T-1 between the sites as well as providing 3 FXO ports for that site. Internally, everything works, Externall...
We have just merged with a company that uses Cisco SPA303 IP phones. These phones are configured to send voicemail to email. They use Exchange 2007, but do not use Unified Communications. I am trying to figure out where this is configured, but I cann...
Hi,Our sales rep has sold a UC540W-BRI-K9 to a customer but the customer doesn't have any BRI connections, they use PSTN lines.The issue is that they have 7 PSTN lines. We can purchase a 4 port FXO interface card but it's not enough to connect all th...
I have 5 voicemail accounts setup. They are all working perfectly except for one users line. It will say his voicemail, then the lady will come on and say "Leave a message after the tone" immediately after that, she says thank you and the phone hang...
Hi,I am having an IP telephony set up with UC 500 with Version 4.2(0).The phones are taking the time from the UC 500 itself.we are having 7942 and 7962 IP Phone models.The isue is that some of the 7942 and 7962 are showing in correct time and some of...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: