Voice Systems and Accessories - Small Business

Upgrade your communication system with our Voice Systems and Accessories, perfect for small businesses.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Forum Posts

I have an auto-offhook (Plar, Hot-Line) configuration set up on my ATA 122.  When I take the phone off-hook the ATA takes 3 seconds to place the call to the network. My dial-plan entry is as follows:<Dial_Plan_1_>( P0 <:4802788500>)</Dial_Plan_1_> I'...

Device: Cisco/SPA508GOld Firmware: 7.4.8a, SIP Capture File NOTIFY-GOOD.capFrame 18: REFER (Supervised transfer) received by phoneFrame 19: INVITE w/ Replaces - New call, that is result of REFERFrame 22: Response 183 for the new callFrame 23: NOTIFY ...

Victor000 by Level 1
  • 1209 Views
  • 1 replies
  • 0 Helpful votes

I'm  new on UC500 series. I want to set up as auto attendant then if nobody press anybody button then Call blast Group then to voicemail.I've already setup auto attendant and verify that it is working properly. I've created Call Blast Group and after...

tcvo91732 by Level 1
  • 1906 Views
  • 8 replies
  • 0 Helpful votes

There have been absolutely no firmware updates in years for SPA 3102Its a pity that SPA 3102 doesn't support TLS + SRTP with SDP (which is the defaultand widely used key exchange mechanism as supposed to some proprietary methodor MIKEY that no one su...

                   I just installed a new UC560 and am ready to convert from our old Panasonic DBS 84 system. The Panasonic is fed by 4 trunk lines that go into two RJ14 trunk connectors. so that each is a Two loop start trunk line plugged into the P...

carlklein by Level 1
  • 1833 Views
  • 5 replies
  • 0 Helpful votes

Hi I have a SPA942 which I have been using for just over 1 yearYesterday I went to it and the screen was blank.Pulling the power and plugging back in causes only the screen to light up but nothing else.The switch port does not light up when power is ...

tim by Level 1
  • 1955 Views
  • 4 replies
  • 0 Helpful votes

Hi,I have a general question around how UC560 operates with IP communicator. Below is my sanitized network diagram of the UC system.Key Pointers:1. I am not routing the phone subnet(10.55.32.0) to my firewall or internal LAN because there is no reaso...

smunzani by Level 1
  • 1588 Views
  • 3 replies
  • 0 Helpful votes

Hi,I am trying to change the default VLAN number for voice to 32 from 100. At the time of apply changes, I get java.lang.nullpointerException error in CCA. If I make changes to the device command line then Cisco would not support + all command line c...

smunzani by Level 1
  • 2119 Views
  • 7 replies
  • 0 Helpful votes

Is it possible to configure the t.37 off ramp on a uc540 to send faxes via email or some type of print driver from local pc's? On ramp and off ramp are installed via cca and on ramp routing works great. Sent from Cisco Technical Support iPhone App

gmeyer by Level 1
  • 1315 Views
  • 5 replies
  • 0 Helpful votes

          I am familiar with the URLs to reboot or cause an SPA5xx/SPA3xx phone to re-provision.  (http://localip/admin/reboot or resync?)          Do to NAT issues, I do not have access to these URLs from my VOIP Server.  Is there a SIP message that...