I've followed and contributed to posts about this problem here: https://supportforums.cisco.com/thread/2057631 But this problem isn't only isolated to 2.5 client, so I thought a new discussion might attract a bit more attention and ...
Morning, I have a Cisco 5520 ASA running 8.4(5). When using a VPN ipsec client, and it connects to the LAN, how does the connection interpret traffic on return. At present I have all my servers pointing to the gateway on our old firewall. I have ...
Hi,I have a Cisco ASA 5512 device. I'm using both clientless SSL vpn. And also IPSEC which is used for our external users who connect using an IPAD and then a remote client to remote desktop into our terminal server.I created the connection using the...
Anyconnect 3.1.02026 works fine on Windows 8 64-bit. But not able to get it to work on Windows 8 32-bit. It says: VPN Service not available. And displays a red cross on Cisco anyconnect client. Any clues?I tested it on Windows8 32-bit VM.
I'm setting up a second exchange 2010 server at a DR location and have been experiencing some problems. The two sites are connected via a pair of ASA5510's using the point to point VPN. I want to rules out any possible VPN issues that may be blocki...
Hi All, I understand IPsec Tunnels are unicast but if I configure for use of IKEv2 on the Site-To-Site VPN can I pass Broadcast and Multicast traffic over the tunnel, rather than configuring some routers to do some GRE encapsulation? I have a pro...
Hi,I am wondering if it is possible to configure a DMVPN, but rather than a spoke site using it's internal IP subnet, it's internal IP subnet is changed to something else when it reaches the hub router. Not really looking for it to do spoke to spoke ...
I have been studying the following document:http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080930f21.shtmland have two questions that I can't seem to find a definitive answer for.1. Does the Certificate server have t...
Hello all,I have the following config below on my ASA5505, where I want to be able to access remote computers who are VPN'd into the inside network, for support purposes.I want to be able to ping the VPN ip from the LAN, and be able to connect to the...
OK, here is my setup: ASA 5505 - 192.168.3.1 PIX 501 - 192.168.1.1 PIX 501 - 192.168.1.2The ASA and the first pix device (192.168.1.1) are connected via site-to-site VPN on the ASA side and the connection works great. I can access hosts...
I have an ASA 5510 and am attempting to audit users logins/logouts. I have logging enabled (with timestamp) and have attempted to setup emails for all VPN client logins. This is what I have put in on the config:smtp-server 10.22.4.50 <-- my Exchang...
HiI am setting up a VPN between my client and their owner, in order for the owner to access ressources at my clients site.Unfortunatly their owner already has an VPN connection to another site with the same subnet as the one on my clients site.I have...
Hi,I am trying to configure Remote Access VPN in our Cicco ASA 5520 firewall through SSL VPN wizard. I tried to configure Anyconnect VPN client option, but after entering user/pass it gives error "An error was received from the secure gateway in resp...
I have configured AnyConnect for remote VPN access and everything works fine minus the annoying warning the pops up when connecting. Users pull an IP address from the pool I created, but are unable to access any network resources on the LAN. I have a...
Both sites have ASA5505 running version 8.2 (5)I am very new to Cisco so please be patient with me I used the site to site VPN wizard which seemed very straight forward and easy. I even watched a tutorial on youtube. I have a solid VPN connection lig...
