Resolved! AnyConnect client on Macbook Air
Hi,For the Anyconnect client on the Macbook Air, 1) Can IPSEC be used?, 2) can split tunneling be disabled?
Hi,For the Anyconnect client on the Macbook Air, 1) Can IPSEC be used?, 2) can split tunneling be disabled?
Hello All,I am kind of new to Cisco and I have no CLI expertise. I need to setup a site-to-site VPN (IPsec tunnel) with NATing. I have previously setup several L2L using ASDM with no problem, none required NATing. Here is the scenario:Site1 uses 192...
Any idea when QucikVPN client for Windows 7 that will work with WRVS4400N v2 will be out?
Hi , How many [concurrent and maximum] roaming user tunnel and site to site vpn tunnels are supported in ISR 2921 .. Any approx count and link to refer . Please suggest .
Hi, We have a router 2911 recently purchased which supports vpn but we are not able to do vpn tunneling, So what is required to use VPN connection. Does ios has to upgrade or some kind of license is required.If license is required then what kind ...
Hi all,does anyone have experience with clientless VPN using selfsigned certificate?I have selfsigned certificate generadted in openssl tool. I have CA certificate imported in ASA and associated appropriate trustpoint. Then I have client certificate ...
Hi, as i have started training on CCIE security version 4, with Networkers Zone, the only istitute for ISE training in India (http://networkerszone.com/), i just wanted to confirm what is the ISE role in version 4 or if it would be...
what is the reason about anyconnect vpn client unable to open xml document or data?It's there anyone else met this problem? And how to solve this problem,can you help me?PS:There is not every pc have this problem.Only some pc have this problem. In wi...
Hello,we have a problem with the anyconnect Client on linux ubuntu. When we try to connect we get the message: No valid certificates available for authenticationWe did an upgrade from the old 2.5.x version - first the connection works, the upgrade wo...
Dear All,can somebody tell me if it would be possible to use Cisco Jabber with Secure Connect (SSL VPN) at the same time as a Cisco Anyconnect Connection?? The reason behind that is, that we have a customer who wants do deploy Cisco Jabber on this co...
Hi All,I have a software VPN client that connects just fine to the PIX 501 VPN, but I cannot ping or telnet to any services on the LAN. Below is my config and results of show cry ipsec sa. I would appreciate any suggestions to fix this. It's been a w...
Hi All,I ahve a requirement to configure static crypto for 1800 site and I need to configure on two sepaarte interfacs at spoke site which means I need to configure 1800*2 = 3600 peers at central site. The challenge I have is due to load balancing , ...
Hello, is it possible to have the ASA connected to two ISP's and use the one ISP connection for Client/S2S VPN and Internet Access and the second ISP connection just for the WebVPN Traffic? How would you manage the Routing, as the default route is po...
Hi,on cisco router we configured remote access vpn but after configuring ip cef command split tunneling stopped working So please anybody have any solution interface Loopback 0 ip address 10.1.1.1 255.255.255.0 ip nat insideip access-list extend...
HiI would like to setup a simple VPN on a small network, nothing special, just to provide access to some simple resources on the network from anywhere. Since I'm not a Cisco expert, I was advised to user a 861 router, but I just can't seem to get the...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-18-2024 07:55 AM | ||
10-17-2024 11:43 PM | ||
10-16-2024 04:00 PM | ||
10-16-2024 05:51 AM | ||
10-15-2024 08:07 AM |
User | Count |
---|---|
10 | |
2 | |
1 | |
1 | |
1 |