VPN

10.1.1.0 <-> Pix 6.3 A <-> 10.72.64.0 <-> Pix 6.3 B <-> 10.1.2.0 <-> router <-> internetI can not access Internet from 10.1.1.0 segment.I've created cryptomap to 10.1.1.0 any, any 10.1.1.0 and it is not working properly.I've debug icmp trace and I sa...

I have several times received this message "%CRYPTO-4-IKMP_NO_SA: IKE message from xx.xx.xx.xx has no SA and is not an initialization offer"on one of my remote site 3745 routers. It is connected to a DSL service and connected via an IPsec tunnel ...

I have many problems with this two pix's to realize a vpn between the firewalls. The PIX 515 is running with a static ip address and the PIX 501 is connected over PPPoE (DSL).In a private lab i want test a L2L vpn connection, this fails likewise. Exi...

Hi,I have PIX 515e with OS 6.3(4) and I have one outside and two inside networks.right now I have these settings (config excerpt):...nameif ethernet0 outside security0nameif ethernet1 inside security100nameif ethernet2 half security50...access-list i...

I have seen some PIX configuration examples that run IPSec over tcp. Does anyone know if the 501 is capable of this? Thanx.Dave

I have a Cisco 804 that I want to simply set an access list on the vty lines to allow telnet from "outside". My ISP provides dynamic IP to the outside interface, so mapping that interface IP address isn't really an option. Can I somehow resolve my ...

Hi,If I enable WebVPN on the 'public' interface, I am unable to manage the VPN 3000 through the public interface. That is, they both seem to be mututally exclusive. Are there any ways to achieve both; Web VPN and VPN3000 Management through 'public' i...

I am using Cisco VPN Client 4.6 to establish an IPSec tunnel w/ a PIX 501. The client is also behind a PIX 501. I can establish the tunnel, but I can't do anything after that. I can't ping any hosts or the gateway at the remote site. When I move ...

Heres the scenario, we have a main office using an 831 that has PPTP connections to it for out of office workers to VPN in using windows PPTP for their VOIP softphones, this part works fine, the problem I ran into last night is, there is a remote use...

Have configured an EasyVPN tunnel for a customer with lots of 10.x.x.x nets. Did not get it working until I changed the VPN office to 192.168.n.n. I the discovered that the central PIX had a 10.0.0.0 0.255.255.255 route back to inside central WAN rou...

Hello.I was using EIGRP and dialer watch for ISDN dial backup from a remote site to our main site. It worked fine, except that whenever I made any modifications to EIGRP (such as adding a new network or modifying the distribute-list) on the main rout...

Hi,ask one question,here is my diagram,R1-------PIX------R2R1 and R2 are Cisco IOS routersR1 has two IPs, 1.1.1.1/24 192.168.1.1/24R2 has two IPs, 2.2.2.2/24 192.168.2.2/24PIX has two IPs,3.3.3.3/24 192.168.3.3/24now, create VPN tunnel between R1 ...

After upgrading my VPN3030s to 4.1.7D the MovianVPN client on PocketPCs are not connecting. I am getting the following error in the VPN logs:Invalid source proxy address: 0.0.0.0! Check private address on remote client.QM FSM error (P2 struct &0x61d...

I have setup vpn tunnel between vpn hardware client 3002 and vpn concentrator 3030. There is a Marconi Video conference device behind vpn 3002 hardware client. There is another marconi video conference device behind vpn concentrator. When connection...

Dear all.I currently have a Cisco Pix Firewall and a VPN Concentrator.I have set up both of these as per the instructions at http://www.cisco.com/en/US/products/hw/vpndevc/ps2284/products_configuration_example09186a00800949d2.shtmlMy problem is that ...