Hello, We have a new site where we are planning on installing brand new WAP units (CW9166I-B) and C9800 WLC. This is a green field deployment. Our wireless vendor is telling us that the CW9166I-B units are Meraki Cloud and not Cisco when you first i...
Forum Posts
Should new RF Profiles be created when deploying new access points at a site, or should the default profile be used?If creating a new RF Profile is recommended, which configuration settings should be modified? We will be deploying CW916xx APs. Any in...
Was there ever a real response / solution to the original question ?Because I think I might have the same problem.9800 -> Configuration -> Services -> Multicast - Wireless mDNS Bridging (enable or disable)What is the equivalent CLI command ?Our scena...
Hi everyone,I have a question about the Cisco Meraki CW9176I and CW9172I access points. While reviewing the installation guide for both models, I found the supported operating capacities based on power source and Ethernet speed, but I couldn't find a...
Hello, I am currently testing a Cisco Catalyst CW9172I Access Point with a Cisco Catalyst 9800 Series Wireless Controller. Environment WLC Model: 9800-L-F-K9Software Version: 17.15.4dAP Model: CW9172ICountry:Taiwan⸻ Issue The AP successfully joins th...
Resolved! EWC AP- subordinates not joining
i have 3 9130axi-d and 3 3802I aps connecting to 3850 switch there is no controller , i have converted one of the 9130 AP to EWC, which is wlc now having version 17.9.10, but rest of the aps are not joining the controller getting obms image failed, i...
Resolved! 9800CL migration to 9800L
Current WLC: C9800-CL on 17.3.5a (Amsterdam) & Current AP version 17.3.5.42AP Models: 1542I/E, 2802I/E, 3802E, 9115AXI, 9120AXI, 9120AXETarget Platform: C9800-L - 17.9.4aCould we migrate on target platform or not, if not please suggest best migration...
Resolved! CW9177 IOS-XE supported release version
Datasheets for the CW9177 say that it is supported by the 26.1.x release. However, when looking at the release notes for 26.1.1 and 26.1.2 it never mentions the CW9177 being supported. Am I missing something?
We are testing 6 GHz on CW9176I APs running MR 32.2.4 and seeing an issue with Windows clients discovering a 6-GHz-only SSID.Test setup:6 GHz onlyWPA3 enabledPMF enabledRADIUS excluded for isolation testingResults:6 GHz-capable iPhone → SSID visible ...
Access points software versions MR 33.1.3 changelogInfoDetailed release notes available at: https://documentation.meraki.com/Wireless/Product_Information/Compatibility_and_Firmware/MR_33.1.3_Release_Notes
Resolved! Re: Wireless Controller 9800 RP port
Hey all,Just wanted to confirm that this also works with the new Cisco WLC 9800H RP using a 1G GLC-SX-MMD SFPAfter spending long time on tshoot, I found that the RP port would not work with a 10G-SR SFP, Once I replaced it with the 1G GLC-SX-MMD, the...
in my home LAB, i have a WLC 2504 running 8.5.102 and i have 2 air-ap2802i-e-k9 access pointsthey are in the same LAN, can ping each other and infact establish connection but terminate immediately.and i think the problem is with the licenses being ma...
I have a 2504 that will not light up. No leds on the front. Appears to have power on the brick. Question - can I use a ASA 5505 power supply on these too? They also have a 48V supply and the plug is the same. Just not sure if the + and - are the s...
Resolved! Wireless Controller 9800 RP port
Hello,I am trying to set up SSO but I struggle to activate RP ports. I have connected them via fiber to swiches in the same vlan and I do not get any link. I do not see that RP port as available port in Web Gui menu redundancy config. I have attached...
Hello Everyone,I am experiencing a weird phenomenon with a couple of APs by one of our clients. The APs (AP 9124AX / 9130AX ) get their IP addresses via DHCP and about 1-3 hours later, they lose the IP Address.I am using a Cisco Catalyst 9800-40 WLC...
