Thank you very much.We are building a wireless LAN network using AP3802i's Mobility Express.We use Mobility Express's internal DHCP to distribute IPv4 addresses to each client.Wireless APs and clients can be connected, but there is a problem with fre...
Forum Posts
Hello All,Could someone please share me the csv file format that is used in location feature which I can use to assign tags to APs using access point MAC address.Please also share how I can add more access point to this newly created location later u...
CLI agent: Error while processing NVGEN command: ... There is an impact to the management GUI + we don't know if running configuration is saved, due to the face each save action results in "CLI agent: Error while processing NVGEN command" warnings. H...
Hello Members, i have Site scenario, We have 12 Access point which is new Catalayst Series AP. Currently we dont have hardware controller. Its working in Embedded WLC mode. Access point itself working as controller. Now we purchased a new 9800 Seri...
I have a situation where I need to advertise WLAN1 along with our standard WLAN2 in one area, while the rest of the area would just have our standard WLAN1. Would the APs be able to roam on WLAN1 This is on AireOS 8.10.190.0 Example below AP group 1 ...
The following errors are logged on the Catalyst9120 AXI:ERR: rdpa_cpu_tx_port_enet_lan # 213: rdpa_cpu_tx_port_enet_lan failed. rdd_rc=120 tx_rdd_error_count=2049 What is the cause of this error and what should I do?
Resolved! AP 1832i Failure
We have seen a very high failure rate for the AIR-AP1832i-B-K9 recently with no known cause. Some displayed a solid amber led and others displayed no led. After swapping out the AP with a spare, the spare comes online right away. Some just go down an...
We have a customer located in the UK with Cat 9800 running both -ROW and -E domain APs. -ROW is the correct domain/country code. They have several C9124AXD deployed, purchased with the -E ETSI domain country code. Now I know this is not technically p...
HI,I have a problem here. The wireless download speed from the intranet server is very slow, but the upload speed is normal. The wired network upload and download are normal.my wlc is 3504 ，ap is AIR-AP2802I-H-K9，Software Version is 8.10.185.0
Resolved! C9115 not able to ping its own interface
HI ALl,i have deploy several EWC and encounter a weird issue with the new arrival of C9115 APs.The AP is loaded with version 16.12.4a and the ap is not able to ping it own WMI interface and GW.i thought it will be due to old firmware version. i upgra...
I am looking for some pointers on how to debug the issue I am facing. Any commands or possible configuration. I have two access points 2802i and 3802i in mobility express controller mode. I am facing very poor performance in 2.4 ghz mode. I get almos...
1 hour and 16 minutes, to download an image from the 9800 on a 10M MPLS circuit. My aps are running in Flexconnect and i've seen where you can modify the capwap window size; however, it's only recommended for use with OEAPs. it doesn't seem to make s...
Hello,As the new Network Admin at our organization, I've taken over responsibility for the wireless infrastructure. While reviewing different WLCs, I found that one has an expiring license. I'm unsure what the license would fall back to. We have a to...
Hi AllI'm currently troubleshooting a 6 GHz only SSID on a 9800 WLC with 17.9.5 and 9166 APs. The SSID is setup with WPA3-Enterprise and SuiteB, as per the guide here:https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-9800-series-wireless-c...
I'm using wireless by connecting USB dongle to my desktop. The problem is that every time the ap reboot, they don't connect immediately, and only when they delete the ssid and reconnect or reset the network. Other aps attached to the same wlc (the de...
